- New
SPC3550BP OPTIBELT is an industrial banded V-belt from the optibelt KB BLUE POWER series, featuring an SPC wedge-belt profile and a datum length Ld of 3550 mm. Its multi-rib construction with a common backing band supports stable operation in industrial belt drive systems. The nominal width of each rib is approximately 22 mm. The number of ribs must be specified when ordering. Specialist B2B industrial supply platform simmering.pl, with worldwide shipping from stock in Poland.
|
Parameter |
Specification |
|---|---|
|
Manufacturer |
OPTIBELT |
|
Product family |
optibelt KB BLUE POWER |
|
Commercial designation |
SPC3550BP |
|
Catalog designation |
SPC KB 3550 BP |
|
Product type |
Banded V-belt |
|
Belt profile |
SPC |
|
Datum length Ld |
3550 mm |
|
Nominal width of each rib |
Approximately 22 mm |
|
Approximate banded profile height |
22.6 mm |
|
Construction |
Multiple V-belt ribs with a common backing band |
|
Execution |
BLUE POWER |
|
Number of ribs |
Must be specified when ordering |
|
Application |
Industrial belt drive systems |
|
Pulley compatibility |
Pulleys with suitable SPC grooves |
The 3550 mm datum length and BP execution for the SPC profile are specified in the manufacturer's product range. The cross-sectional dimensions refer to the SPC profile in its banded construction.
SPC identifies a narrow wedge-belt profile designed to operate in appropriately matched pulley grooves.
The SPC profile has a nominal width of approximately 22 mm.
In a banded V-belt, the profile geometry differs from that of an individual SPC belt primarily because of the common backing band connecting the ribs.
The number 3550 identifies a datum length Ld of 3550 mm.
It does not automatically represent the inside length Li or outside length La.
When selecting a replacement, belt lengths must be compared using the same measurement system.
BP identifies the optibelt BLUE POWER execution within the KB banded V-belt product family.
It does not indicate the number of ribs.
BLUE POWER belts are designed for demanding drive systems requiring high power transmission capability and stable operation.
KB identifies a construction in which several V-belt ribs are connected by a common backing band.
This arrangement restricts independent movement of the individual ribs and helps maintain stable operation within the belt drive.
Each rib operates in a corresponding pulley groove.
Circumferential force is transmitted through friction between the side surfaces of the belt and the pulley groove.
The SPC profile provides the geometry required for compatible industrial wedge-belt pulleys.
The connecting band holds the ribs together as a single assembly.
This is particularly important in drives where individual belts could experience vibration, twisting or uneven operation.
The common backing helps the ribs operate together and reduces the tendency of individual belts to move independently.
Internal tensile members carry the tensile forces generated during power transmission.
Their performance must be considered together with the operating load, pulley diameters, rotational speed and environmental conditions.
The designation SPC3550BP alone does not uniquely identify the number of connected ribs.
OPTIBELT banded V-belt designations normally include the number of ribs before the belt profile.
For example, a designation such as 3-SPB 2000 BP identifies a three-rib banded belt.
Similarly, the complete designation of an SPC belt should specify its rib count.
|
Example designation |
Meaning |
|---|---|
|
2-SPC 3550 BP |
Two-rib banded V-belt |
|
3-SPC 3550 BP |
Three-rib banded V-belt |
|
4-SPC 3550 BP |
Four-rib banded V-belt |
|
5-SPC 3550 BP |
Five-rib banded V-belt |
These examples illustrate the designation structure; availability of each configuration must be confirmed.
The number of ribs must correspond to the actual belt construction and the number of pulley grooves used.
Before ordering, verify the markings on the original belt or consult the drive documentation.
|
Execution |
Construction |
Main difference |
|---|---|---|
|
SPC 3550 SK |
Individual V-belt |
No common backing band |
|
SPC KB 3550 |
Banded V-belt |
Standard banded execution |
|
SPC KB 3550 RP |
RED POWER banded V-belt |
Different product series and construction |
|
SPC KB 3550 BP |
BLUE POWER banded V-belt |
BP execution for demanding industrial drives |
An individual SPC 3550 V-belt and an SPC KB 3550 BP banded V-belt share the same nominal datum length and groove profile.
However, their constructions differ.
The banded version has a common backing connecting the ribs, allowing them to operate as a single assembly.
A banded V-belt should not automatically be replaced with a set of independent V-belts.
OPTIBELT offers different belt series for industrial power transmission applications.
BLUE POWER and RED POWER differ in their construction and operating characteristics.
Selecting the appropriate series requires consideration of transmitted power, rotational speed, pulley diameters, number of ribs and operating conditions.
Identical nominal dimensions do not guarantee complete interchangeability.
Natural written variations include:
SPC3550BP OPTIBELT
OPTIBELT SPC3550BP
SPC 3550 BP
SPC KB 3550 BP
OPTIBELT SPC KB 3550 BP
optibelt KB BLUE POWER SPC 3550
SPC 3550 BP banded V-belt
OPTIBELT SPC 3550 BLUE POWER
These variations help identify the product family but do not replace the complete ordering designation specifying the number of ribs.
Before ordering SPC3550BP OPTIBELT, verify the following parameters:
SPC belt profile.
Datum length Ld of 3550 mm.
Number of connected ribs.
Overall width of the banded belt.
Compatibility with pulley groove geometry.
Driving and driven pulley diameters.
Power transmitted by the drive.
Rotational speed.
Starting conditions and load variations.
Required installation tension.
Operating environment.
Manufacturer's requirements for the specific drive.
The number of ribs directly affects the belt's overall width and the number of pulley grooves engaged.
It is also an important parameter when determining the power transmission capacity of the belt assembly.
A belt with an incorrect rib count may not fit the existing pulley arrangement.
Therefore, SPC3550BP should not be ordered based only on its profile and length when the number of ribs has not been established.
Not automatically.
Although individual SPC belts may fit the same groove profile, they do not have the common backing that characterizes a banded V-belt.
The backing is particularly relevant where the drive experiences vibration, fluctuating loads or operating conditions that could cause independent belt movement.
Any conversion to individual belts requires technical verification of the complete drive.
SPC-profile banded V-belts are used in industrial belt transmissions requiring stable operation of multiple belt ribs.
Depending on drive design and operating requirements, they may be considered for:
Industrial compressors.
Fans and blowers.
Production machinery.
Material handling equipment.
Industrial processing machines.
Heavy-duty drive systems.
Drives subject to fluctuating loads.
These are typical application categories for banded V-belts, not confirmed OEM applications for the exact SPC3550BP designation.
The suitability of the BLUE POWER execution must be established using the operating parameters of the specific drive.
Before installation, inspect pulley grooves for wear, damage and contamination.
The groove geometry must be compatible with the SPC profile.
Worn pulleys may prevent correct belt seating and accelerate belt wear.
Driving and driven pulleys must be correctly aligned.
Misalignment can cause uneven loading across the belt ribs, excessive wear and reduced service life.
Installation tension should follow OPTIBELT recommendations for the specific belt drive.
Insufficient tension can cause slippage and heat generation.
Excessive tension increases loads on shafts and bearings and may reduce component service life.
Do not force the belt over the pulley rim using screwdrivers or other levering tools.
The drive should be sufficiently loosened to allow the belt to be installed without damaging its tensile members or backing band.
All ribs must be correctly seated in their corresponding grooves.
During routine maintenance, check for:
Uneven rib wear.
Cracking or damage to the backing band.
Abnormal vibration.
Belt slippage.
Excessive operating temperature.
Pulley misalignment.
Incorrect tension.
Store the belt in a clean, dry environment away from direct sunlight, oils, solvents and excessive heat.
Avoid sharp bends and deformation during storage.
SPC3550BP OPTIBELT identifies a banded V-belt from the optibelt KB BLUE POWER product family, featuring an SPC profile and a datum length of 3550 mm.
SPC identifies a narrow wedge-belt profile with a nominal individual rib width of approximately 22 mm.
It indicates the datum length Ld of 3550 mm.
BP identifies the BLUE POWER execution manufactured by OPTIBELT.
No. In this product family, BP refers to a banded V-belt execution in which multiple ribs are connected by a common backing band.
The designation SPC3550BP alone does not specify the number of ribs. This must be confirmed using the complete ordering designation.
Not without checking the drive construction. An individual V-belt and a banded V-belt differ in their mechanical arrangement and operating behavior.
No. For the SPC 3550 catalog designation, the stated length refers to the datum length Ld, not the outside length.
SPC3550BP OPTIBELT is an industrial banded V-belt from the optibelt KB BLUE POWER series, featuring an SPC wedge-belt profile and a datum length of 3550 mm. Multiple V-belt ribs are connected by a common backing band to operate as one assembly. The BP execution is intended for demanding power transmission applications. The number of ribs must be confirmed before ordering.
The product is offered through the specialist B2B industrial supply platform simmering.pl, serving industrial procurement departments, technical distributors and maintenance teams, with worldwide shipping from stock in Poland.