CORTECO 01014942 NBR BABSL 105x130x7.5/8.5 mm - Rotary Shaft Oil Seal

CORTECO 01014942 NBR BABSL 105x130x7.5/8.5 mm - Rotary Shaft Oil Seal

CORTECO 01014942 is a rotary shaft oil seal with dimensions 105x130x7.5/8.5 mm, manufactured from NBR. The CORTECO catalogue identifies this specific reference with the design designation BABSL. When selecting a replacement, the complete specification should be considered, including the 105 mm shaft diameter, 130 mm housing diameter, 7.5/8.5 mm width, NBR material and BABSL design.

Technical data - CORTECO 01014942

What does CORTECO 01014942 BABSL mean?

01014942 is the CORTECO catalogue reference identifying this specific rotary shaft seal.

NBR indicates nitrile butadiene rubber, one of the most widely used elastomers for rotary shaft sealing applications, particularly where resistance to mineral oils and lubricants is required.

BABSL is the CORTECO design designation assigned to reference 01014942. This designation is important when identifying or replacing the seal and should not be reduced to a generic oil seal type without confirming the actual construction.

105x130x7.5/8.5 mm defines the catalogue dimensions of this specific seal.

Dimensions of CORTECO 01014942

The confirmed catalogue dimensions are:

• Inside diameter d: 105 mm

• Outside diameter D: 130 mm

• Width: 7.5/8.5 mm

Complete size:

105x130x7.5/8.5 mm

The two width values are part of the catalogue specification and should therefore be retained when identifying the product.

NBR material

CORTECO 01014942 is manufactured from NBR - nitrile butadiene rubber.

NBR is commonly used for rotary shaft seals because of its good resistance to mineral oils, greases and many conventional lubricants. It also provides mechanical properties suitable for a broad range of standard sealing applications.

Material is an important selection parameter. An FPM, ACM or other elastomer seal with identical dimensions should not automatically be considered equivalent to CORTECO 01014942.

BABSL design

The catalogue design designation for CORTECO 01014942 is:

BABSL

This information should be retained when searching for the original product or a technically suitable alternative.

Different CORTECO seals can share the same nominal shaft and housing dimensions while differing in material, lip geometry, width or other construction details.

For precise identification, use the complete specification:

CORTECO 01014942 - NBR - BABSL - 105x130x7.5/8.5 mm

CORTECO 01014942 vs other 105x130 mm seals

A nominal size of 105x130 mm alone does not confirm interchangeability.

CORTECO offers different seal constructions within similar dimensional ranges. Before using another seal as a replacement, verify:

• 105 mm inside diameter

• 130 mm outside diameter

• 7.5/8.5 mm width

• NBR material

• BABSL construction

• sealing lip geometry

• operating medium

• temperature conditions

• shaft speed and operating conditions

Particular attention should be paid to the 7.5/8.5 mm width specification. A conventional 105x130x8 mm or 105x130x12 mm seal should not automatically be considered a direct replacement.

Alternative designations and search references

CORTECO 01014942 may also be searched as:

• CORTECO 01014942

• 01014942 CORTECO

• CORTECO 01014942 105x130x7.5/8.5

• 01014942 105x130x7.5/8.5

• CORTECO BABSL 105x130x7.5/8.5

• BABSL 105x130x7.5/8.5

• CORTECO 105x130x7.5/8.5 NBR

• CORTECO 01014942 oil seal

• CORTECO 01014942 Simmerring

• 105x130x7.5/8.5 NBR oil seal

Selecting a replacement for CORTECO 01014942

The safest method of identification is to use the complete CORTECO reference 01014942.

When selecting an alternative, compare the NBR material, BABSL design and complete 105x130x7.5/8.5 mm dimensions.

If the original seal is available, check the markings on its surface and verify the dimensions of the shaft and housing before installation.

Identical shaft and housing diameters do not automatically mean that two rotary shaft seals are fully interchangeable.

Installation

Before installing the seal, clean the shaft and housing bore thoroughly. The shaft surface in the sealing lip contact area should be checked for scratches, corrosion, excessive wear and grooves.

Protect the sealing lip against sharp edges during installation. The seal should be pressed into the housing evenly and without deformation.

Correct installation is essential for maintaining effective sealing and preventing premature damage to the sealing lip.

FAQ

What are the dimensions of CORTECO 01014942?

CORTECO 01014942 has catalogue dimensions of 105x130x7.5/8.5 mm.

What material is CORTECO 01014942 made from?

The seal is manufactured from NBR - nitrile butadiene rubber.

What is the design of CORTECO 01014942?

The CORTECO catalogue specifies the design as BABSL.

Is CORTECO 01014942 a Simmerring?

Yes. It is a rotary shaft oil seal, commonly referred to as a Simmerring.

Is CORTECO 01014942 the same as a standard 105x130x8 mm oil seal?

It should not automatically be treated as the same product. CORTECO specifies 105x130x7.5/8.5 mm and the BABSL design for reference 01014942.

Can an FPM 105x130 seal replace CORTECO 01014942?

Not automatically. CORTECO 01014942 is specified in NBR. Material compatibility and the complete seal construction must be checked before substitution.

What should be checked when selecting a replacement?

Check the complete 01014942 reference, BABSL construction, NBR material and 105x130x7.5/8.5 mm dimensions. The requirements of the specific sealing application must also be considered.

CORTECO 01014942 - key information

CORTECO 01014942 is an NBR rotary shaft oil seal with catalogue dimensions 105x130x7.5/8.5 mm and CORTECO design designation BABSL. For correct identification or replacement, use the complete part number, dimensions, material and construction rather than selecting a seal solely by its 105x130 mm diameters.

Available from simmering.pl, a specialist supplier of seals and industrial components. Stock in Poland with worldwide shipping.