KINEX 6004 2RS 20x42x12 mm is a single-row deep groove ball bearing with rubber seals on both sides and normally supplied with standard radial internal clearance. The catalog 6004-2RSR execution has a dynamic load rating of 9.38 kN, static load rating of 5.02 kN and grease-lubricated limiting speed of 10,000 rpm. The bearing accommodates radial and limited axial loads in both directions. Specialist B2B industrial supply platform simmering.pl, with worldwide shipping from stock in Poland.
|
Parameter |
Specification |
|---|---|
|
Manufacturer |
KINEX |
|
Complete designation |
6004 2RS |
|
Bearing type |
Deep groove ball bearing |
|
Construction |
Single row |
|
Dimensional series |
60 |
|
Bore diameter d |
20 mm |
|
Outside diameter D |
42 mm |
|
Width B |
12 mm |
|
Nominal dimensions |
20x42x12 mm |
|
Bore type |
Cylindrical |
|
Rolling elements |
Balls |
|
Number of ball rows |
1 |
|
Sealing arrangement |
Rubber seals on both sides |
|
Seal designation |
2RS |
|
Radial internal clearance |
Normal CN, unless otherwise specified |
|
Bearing construction |
Non-separable |
|
Load directions |
Radial and limited axial loads in both directions |
|
Self-aligning capability |
No |
The first digit identifies a single-row deep groove ball bearing.
Its characteristic feature is the deep raceway geometry of the inner and outer rings, between which one row of balls operates.
This construction primarily accommodates radial loads and limited axial loads acting in both directions.
The digit 0 identifies dimensional series 60, characterized by a relatively small bearing cross-section.
For a 20 mm bore diameter, the following standard series are available:
|
Designation |
Dimensions |
|---|---|
|
6004 |
20x42x12 mm |
|
6204 |
20x47x14 mm |
|
6304 |
20x52x15 mm |
|
6404 |
20x72x19 mm |
These bearings differ in outside diameter, width, internal geometry and load-carrying characteristics.
They are not direct dimensional replacements.
Bore code 04 corresponds to a nominal bore diameter of 20 mm.
For standard metric bearing bore codes from 04 upwards, the bore diameter is calculated by multiplying the code by 5 mm.
04 x 5 mm = 20 mm.
The 2RS suffix indicates rubber seals fitted on both sides of the bearing.
KINEX catalog nomenclature also uses the designation 2RSR for executions with contact seals.
The seals perform the following functions:
Restrict dust and fine contaminant ingress.
Help retain grease inside the bearing.
Protect the balls and raceways against abrasive particles.
Reduce lubrication maintenance requirements.
Contact seals generate additional friction, so rotational speed and operating temperature must be considered during bearing selection.
The KINEX 6004 2RS designation does not contain an additional clearance suffix such as C3.
This normally indicates standard radial internal clearance CN.
For single-row deep groove ball bearings with a 20 mm bore diameter, the standard radial internal clearance ranges before installation are:
|
Clearance class |
Range |
|---|---|
|
CN |
5-20 µm |
|
C3 |
13-28 µm |
After installation, operating clearance may decrease due to interference fits and temperature differences between the bearing rings.
CN and C3 executions should not be substituted without checking operating conditions.
The inner ring has a cylindrical bore with a nominal diameter of 20 mm.
Its deep raceway guides the balls and transfers loads from the shaft to the rolling elements.
During interference-fit installation, the ring may expand slightly, reducing internal clearance.
The outer ring has a nominal outside diameter of 42 mm and a width of 12 mm.
Its raceway interacts with the balls, transferring loads into the housing.
Incorrect housing geometry or excessive interference may deform the ring and adversely affect operating conditions.
One row of balls operates between the deep raceways of the bearing rings.
The cage maintains appropriate spacing between the balls and restricts direct ball-to-ball contact.
Pressed steel cages are commonly used in this bearing category. The cage material of the exact KINEX 6004 2RS execution should be confirmed in the manufacturer's documentation.
Two seals close the rolling contact area on both sides of the bearing.
Their purpose is to protect the grease and rolling surfaces against contamination.
The 2RS sealing arrangement does not guarantee complete resistance to water immersion, high-pressure washing or aggressive chemicals.
For the catalog KINEX 6004-2RSR execution, the manufacturer specifies the following values:
|
Parameter |
Value |
|---|---|
|
Basic dynamic load rating Cr |
9.38 kN |
|
Basic static load rating C0r |
5.02 kN |
|
Fatigue load limit Cu |
0.228 kN |
|
Limiting speed with grease lubrication |
10,000 rpm |
|
Minimum chamfer dimension r |
0.6 mm |
|
Catalog mass |
0.070 kg |
These parameters refer to the KINEX 6004-2RSR execution with two contact seals. The commercial designation 6004 2RS should be checked against the manufacturer's marking on the bearing or packaging.
KINEX 6004 2RS is primarily designed to accommodate radial loads acting perpendicular to the shaft axis.
The basic dynamic load rating Cr = 9.38 kN is used to calculate nominal fatigue life.
The basic static load rating C0r = 5.02 kN is used to evaluate the risk of permanent deformation at the ball-to-raceway contact surfaces.
These values are not universal permissible operating loads.
The deep raceways allow the bearing to accommodate limited axial loads in both directions.
The permissible axial force depends on radial loading, internal clearance, rotational speed and lubrication conditions.
When axial loads represent a significant proportion of the total load, the appropriate equivalent load factors must be considered.
When radial and axial loads act simultaneously, the equivalent dynamic bearing load P is calculated using the appropriate X and Y factors for the operating conditions.
For ball bearings, basic rating life is calculated using:
Where:
L10 - basic rating life in millions of revolutions.
C - basic dynamic load rating.
P - equivalent dynamic bearing load.
For example, with a purely radial load of 2.0 kN and P = 2.0 kN:
The calculated basic rating life is approximately 103.2 million revolutions.
This result does not guarantee the actual service life under real operating conditions.
For KINEX 6004-2RSR, the catalog limiting speed with grease lubrication is 10,000 rpm.
For comparison:
|
KINEX execution |
Catalog limiting speed |
|---|---|
|
6004, open, grease lubrication |
17,000 rpm |
|
6004RSR, single contact seal |
11,000 rpm |
|
6004-2RSR, double contact seals |
10,000 rpm |
|
6004-2ZR, double metal shields |
17,000 rpm |
The differences are partly attributable to friction generated by contact seals.
The catalog limiting speed does not mean that continuous operation at this value is possible regardless of temperature and load.
Sealed deep groove ball bearings are generally supplied with factory-applied grease.
The double-sided seals help retain lubricant and restrict contaminant ingress.
Under standard operating conditions, the construction is intended to operate without periodic relubrication.
The exact grease specification and permissible temperature range should be confirmed for the particular execution.
Temperature affects grease viscosity, friction, seal service life and operating clearance.
A higher inner ring temperature relative to the outer ring may reduce internal clearance.
Therefore, mounting fits and temperature differences must be considered when selecting the normal-clearance CN execution.
|
Designation |
Dimensions |
Main difference |
|---|---|---|
|
KINEX 6004 2RS |
20x42x12 mm |
Rubber seals, normal clearance |
|
KINEX 6004 2RS C3 |
20x42x12 mm |
Rubber seals, C3 clearance |
|
KINEX 6004 ZZ |
20x42x12 mm |
Metal shields on both sides |
|
KINEX 6004 |
20x42x12 mm |
Open construction |
|
KINEX 16004 |
20x42x8 mm |
Same bore and outside diameter, smaller width |
|
KINEX 6204 2RS |
20x47x14 mm |
Larger outside diameter and width |
|
KINEX 6304 2RS |
20x52x15 mm |
Larger cross-section |
Both variants have identical dimensions and seals.
They differ in radial internal clearance.
The C3 version has greater clearance before installation, which may be required with tight mounting fits or greater temperature differences.
The CN execution should not automatically be replaced with C3, or vice versa.
The 2RS variant uses rubber contact seals, while ZZ features metal shields.
Rubber seals provide more effective protection against contaminants but generate greater friction.
Metal-shielded executions may be more suitable for higher rotational speeds when environmental conditions permit.
Both bearings have a 20 mm bore diameter and 42 mm outside diameter.
They differ in width:
KINEX 6004 2RS - 12 mm.
KINEX 16004 - 8 mm.
They are not directly interchangeable without verifying the assembly design.
Before purchasing, verify:
Complete KINEX 6004 2RS designation.
Bore diameter of 20 mm.
Outside diameter of 42 mm.
Width of 12 mm.
Sealing arrangement.
Required internal clearance class.
Radial and axial loads.
Rotational speed.
Shaft and housing fits.
Operating temperature.
Lubrication conditions.
Bearings from different manufacturers with identical dimensions may differ in seal material, cage construction, grease specification, load ratings and permissible speed.
Dimensional compatibility of 20x42x12 mm does not automatically guarantee complete technical interchangeability.
KINEX 6004 2RS
6004 2RS KINEX
KINEX 6004-2RS
KINEX 6004-2RSR
6004-2RSR KINEX
6004 2RS 20x42x12
KINEX 6004 ball bearing
6004 2RS single-row deep groove ball bearing
The designation 6004-2RSR is used in the KINEX catalog for the execution with contact seals on both sides. Other written variations may be used as product search references.
Deep groove ball bearings of the 6004 series are used in compact rotating assemblies requiring limited installation space and radial load capacity.
Typical applications of this bearing category include:
Electric motors.
Fans and blowers.
Industrial pumps.
Light-duty drive assemblies.
Conveyor mechanisms.
Production machinery.
Workshop equipment.
Shaft supports.
This is not a confirmed OEM application list for the exact KINEX 6004 2RS product.
Deep groove ball bearings are used to support electric motor rotors.
Selection must consider rotational speed, temperature, mounting fits and required internal clearance.
The seals restrict dust ingress into the bearing.
At higher speeds, additional seal friction and the resulting heat generation must be considered.
Deep groove ball bearings may support pump shafts when loads and environmental conditions are compatible with their specifications.
The 2RS bearing seals do not replace the pump shaft seal protecting against the pumped medium.
Before installation, clean the mounting surfaces and check their dimensions and geometry.
Remove burrs and ensure that the surfaces are free from damage.
Mounting fits should correspond to the load characteristics and operating conditions.
Excessive interference may reduce operating clearance and increase friction and temperature.
When pressing the bearing onto a shaft, apply force to the inner ring.
When installing the bearing into a housing, apply force to the outer ring.
Mounting force must not be transmitted through the balls.
Protect the seals against cuts, deformation and other damage during installation.
Seal damage may cause grease loss and contaminant ingress.
After mounting, check smooth rotation, correct axial positioning and the absence of excessive resistance.
During initial operation, monitoring temperature and vibration is recommended.
Store the bearing in its original packaging in a clean, dry environment.
The bearing has a 20 mm bore diameter, 42 mm outside diameter and 12 mm width.
It indicates two rubber seals fitted on both sides of the bearing. They restrict contaminant ingress and help retain grease.
Without an additional clearance suffix, normal radial internal clearance CN is generally assumed. For a 20 mm bore, the CN range is 5-20 µm before installation.
For the catalog KINEX 6004-2RSR execution, the basic dynamic load rating is 9.38 kN and the basic static load rating is 5.02 kN.
The catalog limiting speed of KINEX 6004-2RSR is 10,000 rpm with grease lubrication.
Not automatically. The C3 version has greater radial internal clearance. Substitution requires verification of mounting fits and operating temperatures.
Sealed deep groove ball bearings of this type are generally supplied with grease and intended to operate without routine relubrication.
Replacement may be possible if the dimensions of 20x42x12 mm, seals, internal clearance, load ratings, rotational speed and other technical requirements are compatible.
KINEX 6004 2RS is a single-row deep groove ball bearing measuring 20x42x12 mm, featuring rubber seals on both sides and normally supplied with standard radial internal clearance. The catalog KINEX 6004-2RSR execution has a dynamic load rating of 9.38 kN, a static load rating of 5.02 kN and a grease-lubricated limiting speed of 10,000 rpm. It accommodates radial and limited bidirectional axial loads.
The product is offered through the specialist B2B industrial supply platform simmering.pl, serving machinery manufacturers, technical distributors, industrial maintenance departments and procurement teams, with worldwide shipping from stock in Poland.
Data sheet
You might also like