NTN 608ZZ/5K 8x22x7 mm single-row deep groove ball bearing with two metal shields (ZZ), pressed steel cage and normal CN radial internal clearance. The /5K suffix identifies Kyodo Yushi Multemp SRL grease. Basic dynamic load rating 3.70 kN, static load rating 1.40 kN and limiting speed 32,000 rpm. Catalogue temperature range -40 to +150°C. Specialist B2B industrial trading platform simmering.pl, with worldwide shipping from stock in Poland.
|
Parameter |
Specification |
|---|---|
|
Manufacturer |
NTN Corporation |
|
Brand |
NTN |
|
Manufacturer's country |
Japan |
|
Full designation |
608ZZ/5K |
|
Commercial designation |
608 ZZ/5K NTN |
|
Bearing type |
Deep groove ball bearing |
|
Construction |
Single-row |
|
Bearing series |
608 |
|
Inside diameter (d) |
8 mm |
|
Outside diameter (D) |
22 mm |
|
Width (B) |
7 mm |
|
Rolling elements |
Balls |
|
Number of rows |
1 |
|
Shields |
Two metal shields, ZZ |
|
Shield design |
Non-contact |
|
Cage |
Pressed steel |
|
Radial internal clearance |
Normal, CN |
|
Lubricant |
Kyodo Yushi Multemp SRL |
|
Special execution |
/5K |
|
Basic dynamic load rating (C) |
3.70 kN |
|
Basic static load rating (C0) |
1.40 kN |
|
Fatigue load limit (Cu) |
0.097 kN |
|
Limiting speed, grease lubrication |
32,000 rpm |
|
Operating temperature range |
-40 to +150°C |
|
Weight |
0.012 kg |
|
Separable construction |
No |
|
Radial load capacity |
Yes |
|
Axial load capacity |
Both directions |
|
EAN/GTIN |
4547359552683 |
The specifications refer to the NTN 608ZZ/5K execution. The /5K suffix is an integral part of the product designation and must not be omitted when identifying or ordering the bearing.
|
Designation element |
Technical meaning |
|---|---|
|
6 |
Deep groove ball bearing |
|
608 |
Bearing series with an 8 mm bore |
|
ZZ |
Two non-contact metal shields |
|
/5K |
Kyodo Yushi Multemp SRL grease specification |
|
NTN |
Japanese rolling bearing manufacturer |
The designation 608 identifies a small deep groove ball bearing with the following nominal dimensions:
Bore diameter: 8 mm.
Outside diameter: 22 mm.
Width: 7 mm.
For the 608 series, the bore diameter is directly identified as 8 mm.
The rule of multiplying the last two digits of a bearing designation by five, commonly used for larger bearings, does not apply to this size.
The ZZ suffix identifies two metal shields, one on each side of the bearing.
These shields help retain grease and limit the entry of contaminants into the rolling contact area.
Their non-contact design avoids continuous sealing friction against the inner ring.
Compared with contact rubber seals, metal shields generally produce lower additional rotational resistance.
However, ZZ shields are not waterproof and do not provide complete protection against fine dust, water or pressurized liquids.
The /5K suffix identifies the grease specification used in this NTN bearing execution.
For NTN 608ZZ/5K, the specified lubricant is Kyodo Yushi Multemp SRL.
This is an important distinction from a standard 608ZZ bearing, which may contain a different factory lubricant.
The /5K suffix does not indicate:
C3 or C5 radial internal clearance.
A special bearing precision class.
A different bore diameter.
A different shield arrangement.
A particular cage material.
A high-speed bearing series.
The suffix must be preserved because the lubricant specification can influence operating temperature, friction, speed capability and service life.
|
Parameter |
Value |
|---|---|
|
Bore diameter (d) |
8 mm |
|
Outside diameter (D) |
22 mm |
|
Width (B) |
7 mm |
|
Minimum chamfer dimension (rs) |
0.3 mm |
|
Weight |
0.012 kg |
|
Parameter |
Value |
|---|---|
|
Minimum shaft shoulder diameter (da) |
10 mm |
|
Maximum housing shoulder diameter (Da) |
20 mm |
|
Maximum fillet radius (ra) |
0.3 mm |
These mounting dimensions are important for correct bearing ring support.
An excessive shaft or housing fillet radius may interfere with the bearing chamfer and prevent proper seating against the supporting shoulder.
The dimensions should be considered together with the specified shaft and housing fits.
The bearing consists of an inner ring, an outer ring, one row of balls, a pressed steel cage and two metal shields.
The inner ring has a nominal bore diameter of 8 mm.
It is mounted on the shaft, and its raceway provides one of the rolling contact surfaces for the balls.
When installed with an interference fit, the inner ring may expand slightly, reducing radial internal clearance.
The outer ring has a nominal outside diameter of 22 mm.
Its raceway guides the rolling elements, while its outside cylindrical surface is used to locate the bearing in the housing.
The pressed steel cage maintains the correct spacing between the balls and prevents direct contact between adjacent rolling elements.
It also contributes to stable ball guidance during rotation.
The two metal shields help protect the internal rolling contact surfaces against contamination and retain the factory lubricant.
Because the shields are non-contact, they generate little additional friction compared with contact sealing arrangements.
The NTN 608ZZ/5K execution has normal CN radial internal clearance.
This clearance is specified before mounting and can change during operation.
The most important factors affecting operating clearance are:
Inner ring interference fit.
Outer ring fit in the housing.
Temperature differences between the bearing rings.
Operating loads and rotational speed.
The normal clearance must not automatically be replaced with C3 simply because the bearing operates at a relatively high rotational speed.
The factory lubricant is a distinguishing feature of NTN 608ZZ/5K.
The lubricant performs several functions inside the bearing:
Reduces friction between rolling contact surfaces.
Limits wear.
Protects metallic surfaces against corrosion.
Contributes to stable operation.
Helps achieve the intended service life.
In a small bearing operating at high speed, lubricant characteristics can significantly influence frictional heat generation and operating temperature.
The catalogue temperature range for this execution is:
-40 to +150°C
This range must be interpreted together with the bearing's loading, speed, fits and lubrication conditions.
It does not guarantee unlimited continuous operation at +150°C under every load and speed combination.
Replacing the factory grease with an arbitrary lubricant is not recommended.
A different grease may have different consistency, base oil viscosity, thickener chemistry and temperature characteristics.
Mixing incompatible greases may also impair lubrication performance.
For applications requiring a different lubricant, an appropriate manufacturer-approved bearing execution should be selected.
The basic dynamic load rating is used to calculate the nominal fatigue life of the bearing.
For ball bearings, the basic rating life equation is:
Where:
L10 - basic rating life in millions of revolutions.
C - basic dynamic load rating.
P - equivalent dynamic bearing load.
The value of 3.70 kN is not a universal maximum permissible operating load.
Actual bearing life depends on the applied load, operating speed, lubrication and other operating conditions.
The basic static load rating is relevant when evaluating loads acting on a stationary bearing or one rotating very slowly.
It is used to assess the risk of permanent deformation at the contact points between the balls and raceways.
The fatigue load limit is used in advanced bearing life calculations that account for operating conditions, lubrication and contamination.
It must not be confused with the basic dynamic load rating or interpreted as the maximum permissible load.
The catalogue limiting speed for grease lubrication is:
32,000 rpm
This value does not mean that continuous operation at 32,000 rpm is permissible under all conditions.
The actual allowable speed depends on:
Bearing loading.
Lubrication conditions.
Operating temperature.
Shaft and housing fits.
Heat dissipation.
Required bearing service life.
|
Bearing variant |
Shields or seals |
Clearance |
Main characteristic |
|---|---|---|---|
|
NTN 608 |
Open |
Standard |
Open bearing construction |
|
NTN 608ZZ |
Two metal shields |
CN |
Standard shielded execution |
|
NTN 608ZZ/5K |
Two metal shields |
CN |
Kyodo Yushi Multemp SRL grease |
|
NTN 608ZZC3/5K |
Two metal shields |
C3 |
/5K lubrication and increased clearance |
|
NTN 608LLU |
Two contact seals |
Depends on execution |
Improved contamination protection |
Both bearings have nominal dimensions of 8x22x7 mm and two metal shields.
The /5K execution specifies Kyodo Yushi Multemp SRL grease.
A standard 608ZZ bearing must not automatically be assumed to contain the same lubricant.
Both variants have ZZ shields and the /5K lubrication designation.
The difference is radial internal clearance:
608ZZ/5K - normal CN clearance.
608ZZC3/5K - increased C3 clearance.
They are not automatically interchangeable despite having identical dimensions.
The 608ZZ/5K uses two non-contact metal shields.
An LLU execution uses contact seals, providing more effective protection against contamination but generally producing additional sealing friction.
The correct selection depends on operating speed, environmental conditions and lubrication requirements.
Natural designation variations include:
NTN 608ZZ/5K
608ZZ/5K NTN
608 ZZ/5K NTN
NTN 608 ZZ/5K
608-ZZ-5K NTN
NTN 608ZZ/5K 8x22x7
The complete catalogue designation 608ZZ/5K should be retained in purchasing documents and product identification.
Removing the /5K suffix would eliminate information about the specified factory lubricant.
These notation variations do not represent separately verified OEM reference numbers.
Before selecting a replacement, verify:
Complete designation 608ZZ/5K.
Dimensions of 8x22x7 mm.
Two non-contact metal shields.
Normal CN radial internal clearance.
Kyodo Yushi Multemp SRL grease specification.
Basic dynamic load rating of 3.70 kN.
Basic static load rating of 1.40 kN.
Required rotational speed.
Operating temperature.
Shaft and housing fits.
Dust contamination and moisture exposure.
Maintaining the specified lubricant is particularly important when the bearing operates under demanding temperature or speed conditions.
Not automatically.
Although the dimensions and shields may match, the factory grease specification may differ.
A replacement should be accepted only after verifying that its lubrication and operating characteristics satisfy the requirements of the application.
The two bearings have the same nominal dimensions and the same /5K lubrication designation, but different radial internal clearances.
The C3 version should only be selected when the operating conditions require increased initial clearance.
Deep groove ball bearings in the 608ZZ series are commonly used in small rotating assemblies, including:
Small electric motors.
Fans.
Guide rollers.
Small conveyor mechanisms.
Compact drive assemblies.
Auxiliary machine mechanisms.
These are typical applications of the general 608ZZ bearing design.
They do not constitute confirmed OEM applications for the exact NTN 608ZZ/5K execution.
The specified /5K grease should be considered when selecting the bearing for a particular machine.
Before mounting, clean the shaft, housing bore and supporting shoulders.
Remove burrs and inspect the mating surfaces for damage.
When installing the inner ring with an interference fit, apply mounting force directly to the inner ring.
Mounting force must never be transmitted through the balls, as this may damage the raceways.
When pressing the outer ring into a housing, apply force directly to the outer ring.
If both rings require interference fits, use an appropriate mounting tool that supports both rings.
Do not deform or pry off the metal shields during installation.
A damaged shield may rub against a bearing ring, increasing rotational resistance and potentially impairing lubrication.
The /5K execution contains a specified factory lubricant.
Do not wash out or replace the grease without confirming that the alternative lubricant is suitable for the bearing and application.
Store the bearing in a clean, dry environment, preferably in its original packaging until installation.
Avoid exposure to moisture, dust and corrosive substances.
The bearing has a bore diameter of 8 mm, an outside diameter of 22 mm and a width of 7 mm.
The /5K suffix identifies the Kyodo Yushi Multemp SRL grease specification. It does not indicate C5 clearance or a precision class.
The bearing has normal CN radial internal clearance.
The manufacturer specifies a pressed steel cage.
The basic dynamic load rating is 3.70 kN, and the basic static load rating is 1.40 kN.
The catalogue limiting speed for grease lubrication is 32,000 rpm. The actual permissible operating speed depends on the application conditions.
Not automatically. They have identical nominal dimensions and the /5K grease specification, but differ in radial internal clearance: CN versus C3.
Only after verifying the application's requirements. A standard 608ZZ may use a different factory lubricant, so matching dimensions and shields do not guarantee complete interchangeability.
NTN 608ZZ/5K is a single-row deep groove ball bearing from Japanese manufacturer NTN, measuring 8x22x7 mm. It features two non-contact metal shields, a pressed steel cage, normal CN radial internal clearance and Kyodo Yushi Multemp SRL grease identified by the /5K suffix. Its basic dynamic load rating is 3.70 kN, while the catalogue limiting speed for grease lubrication is 32,000 rpm.
The specialist B2B industrial trading platform simmering.pl supplies NTN bearings for industrial, maintenance and technical applications. Product selection is based on complete manufacturer designations, catalogue specifications and operating requirements, with worldwide shipping from stock in Poland.
Data sheet