FAG 608 ZZ C3 8x22x7 mm single-row deep groove ball bearing from the Schaeffler Group. Two metal shields (ZZ), corresponding to the 2Z design, and increased C3 radial internal clearance. Non-separable construction designed to accommodate radial and bidirectional axial loads. The exact manufacturer catalogue designation should be verified before selection. Specialist B2B industrial trading platform simmering.pl, with worldwide shipping from stock in Poland.
|
Parameter |
Specification |
|---|---|
|
Brand |
FAG |
|
Manufacturer |
Schaeffler |
|
Designation supplied for identification |
608 ZZ C3 |
|
Bearing type |
Deep groove ball bearing |
|
Construction |
Single-row |
|
Series |
608 |
|
Inside diameter (d) |
8 mm |
|
Outside diameter (D) |
22 mm |
|
Width (B) |
7 mm |
|
Rolling elements |
Balls |
|
Number of rows |
1 |
|
Shields |
Two metal shields, ZZ |
|
Shield design |
Non-contact |
|
Radial internal clearance |
C3, greater than normal |
|
Separable construction |
No |
|
Radial load capacity |
Yes |
|
Axial load capacity |
Both directions |
|
Nominal dimensions |
8x22x7 mm |
The designation 608 ZZ C3 describes a bearing with two metal shields and C3 internal clearance. Schaeffler/FAG also uses the designation 2Z for metal shields. The exact FAG catalogue number should be confirmed before ordering, because the commercial designation ZZ may differ from the manufacturer's official designation.
|
Designation element |
Technical meaning |
|---|---|
|
6 |
Deep groove ball bearing |
|
608 |
Bearing series with an 8 mm bore |
|
ZZ |
Two metal shields |
|
C3 |
Radial internal clearance greater than normal |
|
FAG |
Bearing brand of the Schaeffler Group |
The 608 bearing has the following nominal dimensions:
d = 8 mm.
D = 22 mm.
B = 7 mm.
For the 608 series, the bore diameter is defined directly by the bearing designation. The standard rule of multiplying the last two digits by five, which applies to many larger bearings, does not apply here.
ZZ is a commonly used designation for two metal shields.
In Schaeffler catalogue nomenclature, 2Z identifies two non-contact shields, one on each side of the bearing.
The shields reduce the entry of contaminants and help retain grease inside the bearing.
However, they are not equivalent to contact seals and do not provide a watertight barrier.
C3 indicates radial internal clearance greater than the normal CN class.
This is the initial clearance measured before installation. After the bearing is mounted on the shaft and in the housing, its operating clearance may be smaller.
The operating clearance is affected by:
Inner ring fit.
Outer ring fit.
Temperature differences between the bearing rings.
Loads and operating conditions.
C3 does not automatically indicate longer service life, higher precision or a higher permissible operating speed than a CN bearing.
The inner ring has a nominal bore diameter of 8 mm and is designed for mounting on a shaft.
With an interference fit, the inner ring expands slightly, potentially reducing the bearing's radial internal clearance.
The outer ring has a nominal outside diameter of 22 mm and fits into the housing bore.
Its raceway and the inner ring raceway guide the balls during rotation.
The single-row deep groove ball bearing design primarily accommodates radial loads, while also supporting axial loads in both directions.
The ability to carry axial loads depends on the magnitude of radial loading, operating clearance and service conditions.
The cage maintains appropriate spacing between the balls and reduces direct contact between adjacent rolling elements.
The cage material and exact construction must be confirmed for the specific FAG catalogue number. A pressed steel cage should not automatically be assumed based on specifications from other manufacturers.
Two metal shields reduce contamination entering the bearing and help retain grease inside.
Non-contact shields do not continuously rub against the inner ring, resulting in lower additional friction than contact seals.
However, they do not provide complete protection against water or fine contaminants.
The 608 bearing belongs to the deep groove ball bearing family, designed primarily to accommodate radial loads.
Basic dynamic load rating C and equivalent dynamic bearing load P are used when calculating nominal bearing life.
For ball bearings, the basic rating life equation is:
where L10 represents basic rating life in millions of revolutions.
The C value must be obtained from the documentation for the correct FAG variant, rather than transferred from an SNR 608ZZC3 bearing with identical dimensions.
The bearing can accommodate axial loads acting in both directions.
However, this does not mean that its axial load capacity equals its catalogue radial load rating.
When radial and axial forces act simultaneously, the equivalent dynamic bearing load must be calculated using the manufacturer's appropriate calculation method.
C3 clearance is greater than normal CN clearance before mounting.
During operation, it may decrease due to ring fits and temperature differences.
Insufficient operating clearance can increase temperature and friction. Excessive clearance can reduce shaft guidance accuracy and increase noise.
C3 is neither a precision class nor a speed designation. It is a radial internal clearance class.
Natural commercial designation variations include:
FAG 608 ZZ C3
608 ZZ C3 FAG
FAG 608ZZC3
608ZZC3 FAG
FAG 608-ZZ-C3
608 ZZ C3 8x22x7
FAG 608 ZZ C3 deep groove ball bearing
In Schaeffler nomenclature, two metal shields are identified by the suffix 2Z.
Therefore, the designation 608-2Z-C3 is worth checking when identifying this product.
However, 608-2Z-C3 should not be treated as a confirmed FAG catalogue number for this exact product without checking the manufacturer's documentation or packaging markings.
No OEM reference numbers or EAN codes are provided because they have not been verified.
|
Variant |
Bearing protection |
Radial clearance |
Technical difference |
|---|---|---|---|
|
608 |
No shields |
Normal, unless otherwise specified |
Open construction |
|
608-2Z |
Two metal shields |
Normal, unless otherwise specified |
Non-contact protection |
|
608-2Z-C3 |
Two metal shields |
C3 |
Increased radial internal clearance |
|
608-2RSR |
Two contact seals |
Normal, unless otherwise specified |
Improved protection against contamination |
|
608-2RSR-C3 |
Two contact seals |
C3 |
Contact seals and increased clearance |
The table illustrates construction differences associated with the designations. Availability of each variant under the FAG brand must be confirmed in the current catalogue.
The main difference is internal clearance.
The C3 variant has greater initial radial clearance than a standard bearing with normal clearance.
Changing the clearance class can affect operating temperature, vibration levels and bearing service life.
Both versions may have identical dimensions and C3 clearance, but their protection systems differ.
ZZ metal shields are non-contact and produce little additional friction.
2RS contact seals provide more effective protection against contamination but generate greater friction.
The exact sealing designation must always be interpreted according to the relevant manufacturer's nomenclature.
|
Feature |
FAG 608 ZZ C3 |
SNR 608 ZZ C3 |
|---|---|---|
|
Brand |
FAG |
SNR |
|
Manufacturer group |
Schaeffler |
NTN |
|
Dimensions |
8x22x7 mm |
8x22x7 mm |
|
Bearing type |
Deep groove ball bearing |
Deep groove ball bearing |
|
Shields |
Two metal shields |
Two metal shields |
|
Clearance |
C3 |
C3 |
|
Load ratings and speeds |
Require confirmation for FAG |
According to SNR documentation |
|
Interchangeability |
Requires verification |
Requires verification |
Matching dimensions, shields and clearance class provide a basis for evaluating interchangeability but do not establish identical operating specifications.
Before purchasing, verify:
Complete manufacturer designation on the bearing and packaging.
Dimensions of 8x22x7 mm.
Metal shield design, ZZ or 2Z.
C3 radial internal clearance.
Required shaft and housing fits.
Radial and axial loads.
Rotational speed.
Operating temperature.
Lubrication type and conditions.
Exposure to water, dust and other contaminants.
Noise and vibration requirements.
A bearing from another manufacturer with dimensions of 8x22x7 mm is not necessarily fully interchangeable with FAG 608 ZZ C3.
Maintaining the correct radial internal clearance and shield design is particularly important.
Deep groove ball bearings in the 608 series are used in small rotating mechanisms where compact dimensions and radial load capacity are important.
Typical applications of this bearing design include:
Small electric motors.
Fans.
Guide rollers.
Small conveyor mechanisms.
Compact drive assemblies.
Workshop equipment.
The C3 clearance variant may be appropriate where mounting fits and temperature differences significantly reduce internal clearance during operation.
These are characteristic applications of the 608 bearing family, not confirmed OEM applications of this specific FAG product.
Before installation, clean the shaft and housing surfaces and inspect their condition.
Burrs and contaminants can prevent correct seating of the bearing rings.
When pressing the bearing onto a shaft, mounting force must be applied to the inner ring.
Force must not be transmitted through the balls.
When installing the outer ring with an interference fit, apply force directly to that ring.
If both rings are installed with interference simultaneously, an appropriate mounting tool supporting both rings is required.
Do not deform the metal shields or remove them without a justified maintenance procedure.
A deformed shield may rub against bearing components and increase rotational resistance.
The double-shielded design is intended to operate with grease retained inside the bearing.
The exact factory grease type and its specifications must be confirmed for the particular FAG catalogue number.
Store the bearing in a clean, dry environment, preferably in its original packaging until installation.
The bearing has an inside diameter of 8 mm, an outside diameter of 22 mm and a width of 7 mm.
ZZ indicates two metal dust shields. In Schaeffler nomenclature, the corresponding designation is 2Z.
C3 indicates radial internal clearance greater than normal CN clearance. It does not represent a higher precision class.
No. The C3 variant has increased radial internal clearance, whereas the version without an additional clearance suffix generally corresponds to normal clearance.
They do not provide a watertight seal. They reduce contamination entering the bearing but cannot replace contact seals in wet or heavily contaminated environments.
Double-shielded bearings of this type are generally supplied with grease. The exact grease type and quantity should be confirmed for the specific FAG execution.
This may be possible after comparing the complete designations, load ratings, speeds, shield construction and application requirements. Identical dimensions alone are insufficient.
Non-contact shields help minimize additional friction, but permissible speed depends on the specific bearing execution, grease, loading and temperature. C3 clearance alone does not guarantee higher-speed capability.
FAG 608 ZZ C3 is a single-row deep groove ball bearing measuring 8x22x7 mm, manufactured under the FAG brand of the Schaeffler Group. It features two metal shields (ZZ) and increased C3 radial internal clearance. The bearing accommodates radial and bidirectional axial loads. Selection requires verification of the manufacturer's 2Z designation and the required operating clearance.
The specialist B2B industrial trading platform simmering.pl supplies FAG bearings for industrial, maintenance and technical applications. Product selection is based on complete catalogue designations, dimensions and operating requirements, with worldwide shipping from stock in Poland.
Data sheet