KOYO 6204 2RS 20x47x14 mm single-row deep groove ball bearing with rubber seals on both sides. Basic dynamic load rating 16.0 kN, static load rating 6.65 kN, and catalog limiting speed of 9,700 rpm with grease lubrication. The bearing accommodates radial and limited axial loads in both directions. The 2RS seals protect the balls and raceways against contamination and help retain grease. Specialist B2B industrial supply platform simmering.pl, with worldwide shipping from stock in Poland.
|
Parameter |
Specification |
|---|---|
|
Brand |
KOYO |
|
Complete designation |
6204 2RS |
|
Bearing type |
Deep groove ball bearing |
|
Construction |
Single row |
|
Dimensional series |
62 |
|
Bore diameter d |
20 mm |
|
Outside diameter D |
47 mm |
|
Width B |
14 mm |
|
Nominal dimensions |
20x47x14 mm |
|
Bore type |
Cylindrical |
|
Rolling elements |
Balls |
|
Number of ball rows |
1 |
|
Raceway geometry |
Deep groove |
|
Sealing arrangement |
Rubber seals on both sides |
|
Seal designation |
2RS |
|
Bearing construction |
Non-separable |
|
Primary load direction |
Radial |
|
Axial load capability |
Both directions |
|
Self-aligning capability |
No |
The first digit identifies a single-row deep groove ball bearing.
The bearing contains one row of balls operating between deep raceway grooves in the inner and outer rings.
This geometry enables the bearing to accommodate radial loads and limited axial loads while maintaining relatively low rolling resistance.
The second digit identifies dimensional series 62.
Compared with series 60, series 62 bearings generally have a larger cross-section for the same bore diameter.
For a 20 mm bore, the dimensional differences are:
|
Designation |
Dimensions |
|---|---|
|
6004 |
20x42x12 mm |
|
6204 |
20x47x14 mm |
|
6304 |
20x52x15 mm |
|
6404 |
20x72x19 mm |
These bearing series differ in internal geometry, installation dimensions and load ratings.
They are not direct dimensional replacements.
The bore code 04 corresponds to a nominal bore diameter of 20 mm.
For standard metric bearings with bore codes from 04 upwards:
04 x 5 mm = 20 mm.
The 2RS suffix indicates two rubber seals, one on each side of the bearing.
Their primary functions include:
Restricting the entry of dust and fine contaminants.
Retaining grease inside the bearing.
Protecting the balls and raceways from contamination.
Reducing the need for periodic relubrication.
The 2RS designation describes the general sealing arrangement. The exact sealing lip geometry, elastomer material and contact characteristics should be confirmed using the documentation for the specific KOYO execution.
The inner ring has a nominal cylindrical bore diameter of 20 mm.
Its raceway interacts with the balls and transmits loads from the shaft to the rolling elements.
The shaft fit must be considered during installation because excessive interference can reduce internal clearance and increase operating temperature.
The outer ring has a nominal outside diameter of 47 mm and a width of 14 mm.
Its deep raceway works with the balls to transfer loads into the housing.
Correct housing geometry helps prevent outer ring deformation and uneven load distribution.
One row of balls enables the bearing to accommodate radial and limited axial loads.
The cage maintains appropriate spacing between the balls and prevents direct ball-to-ball contact.
Pressed steel cages are commonly used in deep groove ball bearings of this size. However, the cage material of the exact KOYO 6204 2RS execution should be confirmed.
The seals close the spaces between the inner and outer rings.
Unlike open bearings, the 2RS construction provides additional protection for the lubricant and rolling elements.
However, rubber seals do not guarantee complete resistance to immersion in water, high-pressure washing or aggressive chemicals.
For the 6204 2RS designation, JTEKT/KOYO catalog data provides the following values:
|
Parameter |
Catalog value |
|---|---|
|
Basic dynamic load rating Cr |
16.0 kN |
|
Basic static load rating C0r |
6.65 kN |
|
Fatigue load limit Cu |
0.510 kN |
|
Calculation factor f0 |
13.2 |
|
Limiting speed with grease lubrication |
9,700 rpm |
|
Minimum chamfer dimension r |
1 mm |
|
Minimum shaft shoulder diameter da |
25 mm |
|
Maximum shaft shoulder diameter da |
26.5 mm |
|
Maximum housing shoulder diameter Da |
42 mm |
|
Maximum shoulder fillet radius ra |
1 mm |
|
Catalog mass |
0.106 kg |
KOYO 6204 2RS is primarily designed to accommodate loads acting perpendicular to the shaft axis.
The basic dynamic load rating Cr = 16.0 kN is used to calculate nominal fatigue life.
The basic static load rating C0r = 6.65 kN is used to evaluate loading that may cause permanent deformation at the rolling contact surfaces.
These values are not universal permissible working loads for every operating condition.
Deep raceway grooves allow the bearing to accommodate limited axial loads in both directions.
The permissible axial load depends on radial loading, operating clearance, rotational speed and lubrication conditions.
The bearing should not replace a dedicated thrust bearing in applications dominated by very high axial loads.
When radial and axial loads act simultaneously, the equivalent dynamic bearing load P must be calculated.
The calculation uses the appropriate X and Y factors and the limiting value e, selected according to the manufacturer's technical documentation.
For ball bearings, the basic rating life is calculated using:
Where:
L10 - basic rating life in millions of revolutions.
C - basic dynamic load rating, 16.0 kN for KOYO 6204 2RS.
P - equivalent dynamic bearing load.
For example, with a purely radial load of 2.0 kN and conditions allowing P = 2.0 kN:
The calculated basic rating life is 512 million revolutions.
This is an illustrative calculation, not a guaranteed service life under all operating conditions.
For KOYO 6204 2RS, the manufacturer specifies a catalog limiting speed of 9,700 rpm with grease lubrication.
This value applies under specified catalog conditions. It does not mean the bearing can operate continuously at that speed under any load or temperature.
For comparison, the standard open KOYO 6204 has a higher catalog limiting speed.
The difference is partly attributable to the additional friction generated by contact seals.
The 2RS execution is designed with seals that retain grease inside the bearing.
In typical applications, sealed deep groove ball bearings are supplied factory greased and do not require routine relubrication.
Lubricant service life depends on:
Operating temperature.
Rotational speed.
Load.
Environmental contamination.
Operating duration.
The permissible temperature range depends on the grease, sealing material and cage construction.
The 2RS suffix alone does not establish a specific maximum operating temperature.
|
Designation |
Dimensions |
Main difference |
|---|---|---|
|
KOYO 6204 2RS |
20x47x14 mm |
Rubber seals on both sides |
|
KOYO 6204 |
20x47x14 mm |
Open construction |
|
KOYO 6204 ZZ |
20x47x14 mm |
Metal shields on both sides |
|
KOYO 6204 2RU |
20x47x14 mm |
Different low-friction seal design |
|
KOYO 6204 2RD |
20x47x14 mm |
Alternative sealing arrangement |
|
KOYO 6204 2RS C3 |
20x47x14 mm |
2RS seals and increased radial clearance |
|
KOYO 6004 2RS |
20x42x12 mm |
Smaller outside diameter and width |
|
KOYO 6304 2RS |
20x52x15 mm |
Larger outside diameter and width |
The 2RS variant has rubber seals, while ZZ uses metal shields.
Contact seals generally provide better protection against contaminants but may generate greater friction.
Metal shields do not provide the same sealing barrier as contacting rubber seals.
The 2RU execution uses a sealing design developed with reduced friction in mind.
Selection between 2RS and 2RU should consider contamination protection, rotational speed and operating temperature.
The two executions should not be treated as technically identical.
The C3 variant has greater-than-normal radial internal clearance.
It may be required where tight mounting fits or temperature differences reduce clearance during operation.
C3 is not automatically the better choice. Incorrect operating clearance can increase vibration, noise or uneven load distribution.
Bearing 6004 2RS has dimensions of 20x42x12 mm.
Compared with 6204 2RS:
The bore diameter is identical at 20 mm.
The outside diameter is 5 mm smaller.
The width is 2 mm smaller.
It is not a direct dimensional replacement.
Before ordering KOYO 6204 2RS, verify:
Complete product designation.
Bore diameter of 20 mm.
Outside diameter of 47 mm.
Width of 14 mm.
Rubber seals on both sides.
Required radial internal clearance.
Rotational speed.
Radial and axial loads.
Operating temperature.
Shaft and housing fits.
Lubrication requirements.
Cage construction, where relevant.
Particular attention should be paid to the sealing arrangement and internal clearance.
Bearings from other manufacturers with dimensions of 20x47x14 mm may have similar construction but differ in sealing material, grease, cage, load ratings and permissible speed.
Identical dimensions do not guarantee complete technical interchangeability.
Natural designation variants include:
KOYO 6204 2RS
6204 2RS KOYO
KOYO 6204-2RS
6204-2RS KOYO
KOYO6204 2RS
6204 2RS 20x47x14
KOYO 6204 2RS ball bearing
6204 2RS single-row deep groove ball bearing
These designation variations help identify the product but do not replace verification of the manufacturer's complete designation.
Deep groove ball bearings of the 6204 series are used in rotating assemblies requiring compact construction, low rolling resistance and the ability to accommodate radial and limited axial loads.
Typical applications for this bearing category include:
Electric motors.
Fans and blowers.
Industrial pumps.
Gearboxes and drive assemblies.
Conveyor mechanisms.
Production machinery.
Workshop equipment.
Rotating shaft supports in mechanical equipment.
These are general applications based on bearing construction, not confirmed OEM applications for the exact KOYO 6204 2RS designation.
Deep groove ball bearings are frequently used to support electric motor rotors.
Selection must consider rotational speed, temperature, mounting fits and required internal clearance.
Double-sided seals help protect the rolling elements against dust present in the surrounding environment.
Operating temperature and rotational speed remain important selection factors.
The bearing may be used in suitably designed power transmission assemblies.
Selection must account for radial and axial forces and lubrication conditions.
Clean the shaft and bearing housing before installation.
The mounting surfaces should be free from burrs, corrosion and mechanical damage.
Inner and outer ring fits must be selected according to the loading conditions.
Excessive interference may reduce internal clearance, while insufficient interference may allow unwanted movement between the bearing rings and their seating surfaces.
When pressing the bearing onto a shaft, apply force to the inner ring.
When installing the bearing into a housing, apply force to the outer ring.
Mounting force must not be transmitted through the balls.
Avoid damaging the rubber seals during installation.
Damaged seals may lead to grease loss and contamination of the bearing interior.
After mounting, check:
Smooth rotation.
Correct axial location.
Absence of excessive resistance.
Shaft-to-housing alignment.
Absence of seal damage.
Store the bearing in its original packaging in a clean, dry environment.
Protect it against moisture, contamination and mechanical damage before installation.
The bearing has a 20 mm bore diameter, 47 mm outside diameter and 14 mm width.
The 2RS suffix indicates rubber seals on both sides, which restrict contaminant ingress and help retain grease.
The basic dynamic load rating is 16.0 kN, while the basic static load rating is 6.65 kN.
The catalog limiting speed with grease lubrication is 9,700 rpm. The actual permissible operating speed depends on load and operating conditions.
No. Both variants have identical nominal dimensions, but 2RS uses rubber seals while ZZ uses metal shields. They differ in contamination protection and friction characteristics.
Only after verifying the required operating clearance. The C3 version has greater radial internal clearance than normal, which is not suitable for every application.
Sealed deep groove ball bearings are generally supplied with grease. The exact grease specification and operating conditions should be confirmed for the supplied execution.
Replacement may be possible if not only the dimensions of 20x47x14 mm match, but also the seal type, internal clearance, load ratings, permissible speed and other technical requirements.
KOYO 6204 2RS is a single-row deep groove ball bearing measuring 20x47x14 mm, equipped with rubber contact seals on both sides. Its basic dynamic load rating is 16.0 kN, static load rating is 6.65 kN, and catalog limiting speed with grease lubrication is 9,700 rpm. The bearing accommodates radial and limited axial loads in both directions.
The product is offered through the specialist B2B industrial supply platform simmering.pl, serving industrial maintenance departments, machinery manufacturers, technical distributors and industrial procurement teams, with worldwide shipping from stock in Poland.
Data sheet