Viton 14x2.5 mm FKM/FPM O-ring with a 14 mm inner diameter, 2.5 mm cross-section and 19 mm nominal outer diameter. FKM fluoroelastomer offers resistance to many mineral oils, fuels and elevated temperatures. FKM and FPM designate the same elastomer family, while Viton® is a registered trademark. Correct selection requires verification of compound formulation, hardness, operating medium and sealing groove geometry.
|
Parameter |
Specification |
|---|---|
|
Product type |
O-ring – Circular cross-section sealing ring |
|
Product designation |
Viton 14x2.5 FKM/FPM |
|
Material |
FKM / FPM – Fluoroelastomer |
|
Material trade name |
Viton® – Registered trademark for specific fluoroelastomers |
|
Inner diameter (d1) |
14 mm |
|
Cross-section diameter (d2) |
2.5 mm |
|
Nominal outer diameter |
19 mm |
|
Nominal dimensions |
14x2.5 mm |
|
Cross-section profile |
Circular |
|
Sealing application |
Static; dynamic subject to operating condition verification |
|
Shore A hardness |
Not confirmed |
|
Dimensional standard |
Not confirmed |
|
Intended function |
Sealing mechanical connections, hydraulic assemblies and technical installations |
Important material identification: FKM and FPM designate the same family of fluoroelastomers. Viton® is a registered trademark for specific FKM materials. Without confirmation from the manufacturer, the use of genuine Viton® elastomer cannot be guaranteed.
The Viton 14x2.5 mm FKM/FPM O-ring is an elastomeric sealing ring with a circular cross-section. Its primary function is to prevent or restrict the passage of liquids and gases through clearances between mating mechanical components.
Sealing is achieved through controlled deformation of the ring inside a properly designed installation groove.
When the mechanical connection is assembled, the O-ring cross-section is compressed between the sealing surfaces. The elasticity of the fluoroelastomer generates contact pressure, creating a barrier that restricts leakage from the sealed area.
Under operating pressure, the O-ring may be pressed further against the groove surfaces. However, excessive installation clearance or unsuitable elastomer hardness can lead to material extrusion into the clearance gap.
14 mm – Nominal inner diameter.
2.5 mm – Nominal cross-section diameter.
19 mm – Nominal outer diameter.
The nominal outer diameter is calculated as follows:
The 19 mm value represents the calculated nominal outer diameter. Actual manufacturing tolerances must be confirmed against the manufacturer's documentation.
FKM/FPM is a family of fluoroelastomers used in sealing applications requiring resistance to many petroleum-derived substances, oils, fuels and elevated temperatures.
Compared with numerous conventional NBR compounds, FKM elastomers generally provide improved thermal stability and resistance to selected chemical substances.
Mineral oils – Very good resistance of many FKM compounds to mineral-based lubricating and hydraulic oils.
Hydrocarbon fuels – Favorable resistance to numerous gasoline formulations, diesel fuels and petroleum-derived products.
Aliphatic and aromatic hydrocarbons – Good compatibility of many compounds, depending on the chemical composition of the medium.
Elevated temperatures – Favorable thermal stability compared with many standard NBR elastomers.
Ozone and atmospheric aging – Very good resistance characteristic of fluoroelastomer materials.
Aging resistance – Potential to retain sealing properties under demanding operating conditions, depending on the specific compound.
FKM is not universally resistant to all chemical substances.
Particular verification is required for:
Ketones, including acetone.
Certain esters and polar solvents.
Ammonia and selected amine compounds.
Hot water and steam.
Strongly alkaline chemical environments.
Specialized hydraulic fluids containing aggressive additives.
Certain specially formulated FKM compounds may provide different chemical resistance characteristics from conventional fluoroelastomers.
Material compatibility must be confirmed for the specific FKM compound, considering the operating medium, temperature, concentration and exposure duration.
Sealing effectiveness depends on elastomer properties, groove geometry and operating conditions.
|
Parameter |
Technical significance |
|---|---|
|
Operating temperature |
Influences elasticity, aging and FKM durability |
|
Operating pressure |
Determines sealing load and extrusion risk |
|
Shore A hardness |
Influences deformation and extrusion resistance |
|
Compression ratio |
Determines initial sealing contact pressure |
|
Groove fill |
Must accommodate elastomer deformation and thermal expansion |
|
Installation clearance |
Influences extrusion risk under pressure |
|
Operating medium |
Determines chemical compatibility requirements |
|
Relative movement |
Influences friction, wear and lubrication requirements |
The FKM/FPM designation alone does not establish the permissible operating temperature, maximum pressure or hardness of the specific O-ring.
High-pressure applications may require backup rings to reduce the risk of elastomer extrusion into the installation clearance.
For dynamic sealing applications, friction, lubrication and the movement characteristics of the mating components must also be evaluated.
FKM O-rings with a 2.5 mm cross-section may be used in mechanical connections requiring a relatively small sealing element with specific chemical resistance properties.
Typical application areas include:
Industrial valves and fittings.
Hydraulic system connections.
Pumps and oil system components.
Fuel systems.
Technical connectors and fittings.
Industrial instrumentation components.
Selected process installations.
Mechanical assemblies requiring sealing at elevated temperatures.
These are general applications of FKM sealing materials. They do not confirm compatibility of the specific 14x2.5 mm O-ring with any particular equipment.
|
Property |
FKM/FPM |
NBR |
EPDM |
|---|---|---|---|
|
Many mineral oils |
Very good resistance |
Good resistance |
Generally unsuitable |
|
Many hydrocarbon fuels |
Good to very good |
Compound-dependent |
Generally unsuitable |
|
Elevated temperatures |
Favorable resistance |
More limited |
Favorable in compatible media |
|
Ozone and atmospheric aging |
Very good resistance |
Limited resistance |
Very good resistance |
|
Hot water and steam |
Requires specific verification |
Compound-dependent |
Often more suitable |
|
Ketones |
Conventional compounds generally unsuitable |
Generally unsuitable |
Often good resistance |
|
Interchangeability |
Requires verification |
Requires verification |
Requires verification |
FKM may be more suitable than NBR in certain oil and fuel applications, particularly at elevated temperatures.
However, this does not mean that FKM is compatible with every operating medium or automatically interchangeable with other elastomers.
The comparison describes general characteristics of material families rather than guaranteed properties of a specific compound.
When selecting the Viton 14x2.5 mm FKM/FPM O-ring, verify:
Nominal inner diameter of 14 mm.
Nominal cross-section diameter of 2.5 mm.
Installation groove geometry.
Required compression ratio.
Permissible stretching during installation.
FKM compound hardness.
Compatibility with the operating medium.
Operating temperature and pressure.
Installation clearance.
Static or dynamic sealing requirements.
An FKM 14x2.5 mm O-ring is not automatically interchangeable with an NBR 14x2.5 mm O-ring.
Despite identical nominal dimensions, these materials differ in chemical resistance, thermal properties and deformation behavior.
Before replacement, verify hardness, operating medium and mechanical design requirements.
Viton® is a registered trademark for specific fluoroelastomer materials.
Not every O-ring designated FKM or FPM is manufactured from genuine Viton® elastomer.
Confirmation of material origin requires appropriate manufacturer documentation.
Correct installation is essential for maintaining sealing performance and reducing the risk of elastomer damage.
Before installation:
Clean the sealing groove and mating surfaces.
Remove sharp edges, burrs and contaminants.
Inspect the ring for cracks, cuts and deformation.
Prevent twisting during installation.
Avoid excessive stretching.
Use an installation lubricant compatible with FKM and the operating medium when required.
Verify correct positioning before closing the connection.
With a 2.5 mm cross-section, proper groove dimensions are particularly important. Incorrect compression may result in insufficient sealing contact pressure or excessive elastomer deformation.
For dynamic applications, lubrication conditions, movement speed and the condition of mating surfaces must also be considered.
The inner diameter is 14 mm, the cross-section diameter is 2.5 mm and the nominal outer diameter is 19 mm.
Yes. FKM and FPM designate the same family of fluoroelastomers, using terminology from different material classification systems.
No. Viton® is a registered trademark for specific fluoroelastomers. The FKM designation alone does not confirm the use of genuine Viton® material.
Many FKM compounds offer good resistance to gasoline and hydrocarbon fuels. Compatibility with a specific fuel formulation must be verified.
It may be used in appropriately designed hydraulic systems when the material is compatible with the hydraulic fluid and the groove geometry and operating conditions meet the application requirements.
The permissible temperature range depends on the specific FKM compound. Reliable operating limits cannot be established without confirmation of its material properties.
Replacement requires verification of chemical compatibility, hardness, temperature and operating conditions. Identical dimensions do not guarantee interchangeability.
FKM O-rings may be used in selected dynamic applications after verification of groove design, lubrication, movement speed and elastomer properties.
The Viton 14x2.5 mm FKM/FPM O-ring is a circular sealing ring with a 14 mm inner diameter, 2.5 mm cross-section and 19 mm nominal outer diameter. FKM fluoroelastomer offers resistance to many mineral oils, fuels and elevated temperatures. Viton® is a registered trademark for specific FKM materials. Correct selection requires verification of compound formulation, hardness, operating medium and groove geometry.
The specialist B2B industrial trading platform simmering.pl supplies FKM/FPM O-rings for industrial sealing applications, including the 14x2.5 mm configuration. Product availability, compound hardness, confirmation of genuine Viton® material origin and delivery times are subject to verification.
You might also like