GRN 70x95x13 VMQ/MVQ AO TC is a double-lip silicone rotary shaft oil seal featuring a spring-loaded primary sealing lip, an auxiliary dust lip, metal reinforcement and an elastomer-coated outside diameter. Silicone rubber provides excellent low-temperature flexibility and good resistance to elevated temperatures. Selection requires verification of medium compatibility, operating temperature, shaft speed and lubrication conditions. Specialist B2B industrial supply platform simmering.pl, with worldwide shipping from stock in Poland.
|
Parameter |
Specification |
|---|---|
|
Brand |
GRN |
|
Product designation |
70x95x13 AO TC VMQ/MVQ |
|
Product type |
Radial rotary shaft seal |
|
Technical description |
Double-lip silicone oil seal |
|
Seal design |
AO / TC |
|
Nominal inside diameter d |
70 mm |
|
Nominal outside diameter D |
95 mm |
|
Nominal width b |
13 mm |
|
Dimensions |
70x95x13 mm |
|
Elastomer material |
VMQ / MVQ - silicone rubber |
|
Number of lips |
2 |
|
Primary sealing lip |
Spring-loaded |
|
Auxiliary lip |
Dust-exclusion lip |
|
Garter spring |
Yes |
|
Reinforcing case |
Metal |
|
Outside surface |
Elastomer-coated |
|
Sealing principle |
Dynamic contact sealing |
|
Application |
Rotating shafts |
|
Nominal shaft diameter |
70 mm |
|
Nominal housing bore diameter |
95 mm |
|
Directional pumping features |
Not specified in the designation |
|
Sealed medium |
Subject to chemical compatibility with VMQ |
|
Primary lip lubrication |
Required |
|
Maximum shaft surface speed |
Requires confirmation for the specific execution |
|
Maximum operating pressure |
Requires confirmation for the specific execution |
|
Operating temperature range |
Depends on the silicone compound |
The dimensions, material and basic construction are identified by the product designation. Specific operating limits, including temperature, shaft surface speed, pressure and elastomer hardness, must be confirmed using technical documentation for the exact GRN execution.
The first number identifies the nominal shaft diameter of 70 mm.
The primary sealing lip is designed to operate against a properly prepared shaft surface of this diameter.
Correct selection requires suitable dimensional tolerances, surface roughness and shaft geometry.
The second number indicates the nominal outside diameter of the seal, which is 95 mm.
This corresponds to the nominal housing bore diameter.
The elastomer-coated outside surface helps establish static sealing between the seal body and the housing.
The third number identifies the nominal axial width of 13 mm.
When replacing the seal, the housing depth and available installation space must be checked.
The 13 mm width also influences the axial position of the sealing lip relative to the shaft contact surface.
The AO and TC designations identify a radial shaft seal with an additional dust-exclusion lip.
In the terminology used for GRN seals:
AO - double-lip radial shaft seal design.
TC - construction with an elastomer-coated outside diameter, a spring-loaded primary sealing lip and an additional dust lip.
In practice, AO and TC describe corresponding basic construction types.
However, this does not automatically establish interchangeability between products manufactured from different materials or with different detailed specifications.
VMQ identifies silicone rubber based on methyl-vinyl siloxane polymers.
The alternative designation MVQ is also encountered in commercial product descriptions.
This material is characterized by:
Excellent flexibility at low temperatures.
Good resistance to elevated temperatures.
Resistance to ozone.
Resistance to atmospheric aging.
Retention of elastic properties across a broad temperature range.
However, silicone rubber has limitations concerning abrasion resistance, tear resistance and compatibility with certain oils and solvents.
The primary lip is responsible for restricting lubricant leakage along the rotating shaft.
Its flexible sealing edge maintains contact with the shaft surface.
Under correct operating conditions, a thin lubricating film should exist between the lip and the shaft.
This film reduces friction and helps limit wear of the contacting surfaces.
Insufficient lubrication can cause excessive heat generation and accelerated sealing lip deterioration.
The primary sealing lip is supported by a circumferential garter spring.
The spring helps maintain appropriate sealing contact pressure during operation.
This is particularly important when temperatures change, minor geometric deviations occur or the sealing contact gradually wears.
The spring must not be removed or modified.
The second lip is positioned on the external side of the seal.
Its function is to restrict dust and other contaminants from entering the primary sealing area.
The auxiliary lip is not a second independent oil-retaining seal.
It also does not automatically provide protection against pressurized water.
The metal case provides structural rigidity and helps maintain the correct seal geometry during installation.
It reduces the risk of housing deformation when the seal is correctly pressed into its mounting bore.
The outside surface is covered with elastomer.
This construction helps seal the interface between the seal body and housing bore.
Static sealing at this interface is just as important as dynamic sealing against the rotating shaft.
VMQ silicone rubber maintains favorable elastic properties at elevated temperatures.
Depending on the formulation, general VMQ material temperature ranges may extend to approximately +200°C.
However, this does not mean that the specific GRN 70x95x13 oil seal can operate at that temperature under all conditions.
In a dynamic sealing application, the temperature at the lip-to-shaft contact may exceed the surrounding ambient temperature.
Factors affecting contact temperature include:
Shaft surface speed.
Sealing lip contact pressure.
Lubricant type.
Heat dissipation conditions.
Shaft surface condition.
Therefore, the maximum permissible temperature must be evaluated for the complete sealing arrangement.
One of the most important advantages of VMQ is its ability to retain flexibility at low temperatures.
Depending on the formulation, silicone rubber may maintain useful properties at temperatures approaching -50°C.
This is a general material characteristic, not a confirmed minimum operating temperature for this particular seal.
Low-temperature flexibility can help the sealing lip maintain contact with the shaft in equipment operating in cold environments.
VMQ provides good resistance to ozone, oxygen and atmospheric exposure.
These properties are relevant to elastomer durability during storage and operation.
Compared with NBR and certain other elastomers, silicone rubber may exhibit lower resistance to tearing and abrasion.
Consequently, VMQ selection should account for the mechanical operating conditions of the sealing lip.
High temperature alone is not sufficient justification for automatically replacing every NBR seal with a silicone seal.
|
Medium or operating condition |
General VMQ characteristics |
|---|---|
|
Air |
Very good resistance |
|
Ozone |
Very good resistance |
|
Low temperatures |
Excellent flexibility |
|
Elevated temperatures |
Good material resistance |
|
Selected mineral oils |
Compatibility depends on oil composition and elastomer formulation |
|
Industrial greases |
Verification required |
|
Gasoline |
Generally not recommended |
|
Aromatic solvents |
Generally not recommended |
|
Strong acids and alkalis |
Individual assessment required |
|
Steam |
Potential limitations depending on operating conditions |
This table provides general material information and does not constitute confirmed chemical compatibility for the exact GRN product.
Different oils contain different base fluids and additive packages.
Certain components may cause elastomer swelling, changes in hardness or deterioration of mechanical properties.
Therefore, seal selection should consider the specific lubricant rather than relying only on the general term "oil."
|
Material |
Main advantages |
Typical limitations |
|---|---|---|
|
VMQ/MVQ |
Low-temperature flexibility and heat resistance |
Limited abrasion and tear resistance |
|
NBR |
Good resistance to many mineral oils and favorable mechanical properties |
Lower high-temperature resistance |
|
FKM/FPM |
High thermal and chemical resistance with compatible media |
Low-temperature limitations depending on compound |
|
ACM |
Good resistance to hot oils in suitable applications |
Limitations involving certain media and low temperatures |
NBR is widely used in rotary shaft seals because of its resistance to many mineral oils and favorable mechanical properties.
VMQ may be more appropriate where flexibility at very low temperatures is required.
However, VMQ should not automatically be expected to provide a longer service life.
FKM is frequently used in demanding oil-sealing applications at elevated temperatures.
VMQ is particularly notable for its low-temperature flexibility.
The two materials differ in chemical and mechanical resistance, so interchangeability requires verification of the actual operating conditions.
|
Feature |
AO / TC |
SC |
|---|---|---|
|
Primary sealing lip |
Yes |
Yes |
|
Garter spring |
Yes |
Yes |
|
Additional dust lip |
Yes |
No |
|
Elastomer-coated outside diameter |
Yes |
Yes |
|
Dust protection |
Additional lip |
No additional lip |
|
Frictional resistance |
May be higher |
Generally lower |
|
Primary application |
Shaft sealing with additional contamination protection |
Standard rotary shaft sealing |
The AO/TC design is useful when lubricant retention must be combined with additional protection of the sealing contact against external contaminants.
However, a standard double-lip seal does not replace specialized sealing systems designed for severe dust exposure, mud or pressurized water.
Common product designation variations include:
GRN 70x95x13 VMQ AO TC
GRN 70x95x13 MVQ AO TC
GRN 70x95x13 silicone oil seal
70x95x13 VMQ rotary shaft seal
70x95x13 VMQ TC
70x95x13 MVQ AO
GRN TC 70x95x13 silicone
70x95x13 VMQ double-lip oil seal
70x95x13 AO TC silicone shaft seal
GRN 70x95x13 silicone rotary shaft seal
These are alternative search descriptions, not verified replacement part numbers from other manufacturers.
Before ordering the GRN 70x95x13 VMQ/MVQ AO TC oil seal, verify:
Nominal shaft diameter: 70 mm.
Nominal housing bore diameter: 95 mm.
Seal width: 13 mm.
AO/TC construction.
VMQ/MVQ silicone material.
Spring-loaded primary sealing lip.
Additional dust-exclusion lip.
Type of sealed medium.
Operating temperature.
Shaft surface speed.
Shaft surface condition and roughness.
Pressure inside the sealed housing.
Lubrication conditions.
Dimensions of 70x95x13 mm alone are insufficient to confirm complete interchangeability between rotary shaft seals.
The elastomer material, sealing lip geometry and operating conditions are also essential.
Such a replacement may be possible, but it should not be based solely on dimensional compatibility.
Chemical compatibility, temperature, shaft surface speed and mechanical loading of the sealing lip must be checked.
Direct interchangeability should not be assumed.
Changing the seal width can affect the position of the sealing lip relative to the shaft, seating within the housing and available installation space.
Any such substitution requires an assessment of the equipment design.
Silicone radial shaft seals may be used in equipment where temperature resistance and elastomer flexibility are important.
Potential application categories include:
Industrial rotating assemblies.
Production machinery.
Mechanisms with 70 mm diameter shafts.
Equipment operating under changing temperature conditions.
Selected gearboxes and mechanical assemblies using media compatible with VMQ.
Equipment requiring additional protection of the sealing area against dust.
These are general application categories for AO/TC seals manufactured from VMQ, not a confirmed list of OEM applications for the exact GRN product.
Before installation, inspect the shaft contact surface.
It must be clean, sufficiently smooth and free from damage.
Wear grooves, corrosion and sharp edges can damage the sealing lip or cause leakage.
During installation, avoid pulling the lip directly across threads, grooves or sharp edges.
Use a protective installation sleeve where necessary.
Silicone rubber can be particularly vulnerable to mechanical damage caused by incorrect installation.
Before starting the equipment, provide suitable lubrication at the primary sealing lip.
The lubricant must be compatible with VMQ silicone rubber.
Dry running must be avoided.
In a typical arrangement, the primary spring-loaded sealing lip should face the medium being retained.
The auxiliary dust lip should face the external environment.
Press the seal evenly into the housing using an appropriate installation tool.
Do not strike the elastomer directly or deform the metal reinforcing case.
After installation, verify correct seating and the position of the sealing lip and garter spring.
The nominal dimensions are 70x95x13 mm. The seal is designed for a 70 mm shaft and a 95 mm housing bore.
VMQ/MVQ identifies silicone rubber. This material offers good resistance to elevated temperatures and maintains flexibility at low temperatures.
AO/TC identifies a double-lip construction with a spring-loaded primary sealing lip and an additional dust-exclusion lip.
Yes. The AO/TC design includes a circumferential garter spring supporting the primary sealing lip.
It may be suitable for selected oils, but compatibility depends on the specific VMQ formulation, lubricant composition, temperature and operating conditions.
Not in every application. VMQ is particularly suitable where low-temperature flexibility is important, while NBR may provide better mechanical resistance and compatibility with many mineral oils.
Yes. The additional dust lip helps restrict contamination from reaching the primary sealing contact. However, it does not provide complete protection against every type of contamination.
Direct interchangeability should not be assumed. The difference in width may affect seal seating and the position of the sealing lip relative to the shaft.
GRN 70x95x13 AO TC VMQ/MVQ is a double-lip silicone rotary shaft oil seal. It features a spring-loaded primary sealing lip, an auxiliary dust lip, metal reinforcement and an elastomer-coated outside diameter. VMQ provides low-temperature flexibility and good heat resistance. Proper selection requires verification of medium compatibility, shaft speed and lubrication conditions.
The product is offered through the specialist B2B industrial supply platform simmering.pl, serving industrial procurement departments, technical distributors and maintenance teams, with worldwide shipping from stock in Poland.
Data sheet
You might also like