- New
ZEN AX 1022 is a single-direction axial needle roller bearing measuring 10x22x2.80 mm. Inside diameter: 10 mm; outside diameter: 22 mm; height: 2.80 mm. Features cylindrical needle rollers and a pressed steel cage. Designed to accommodate axial loads in compact mechanical assemblies. The AX series differs from AXK and is not supplied as a complete arrangement with two separate thrust washers. Available through the specialist B2B industrial supply platform simmering.pl, with worldwide shipping from stock in Poland.
|
Parameter |
Specification |
|---|---|
|
Manufacturer |
ZEN |
|
Complete designation |
AX 1022 |
|
Bearing type |
Axial needle roller bearing |
|
Series |
AX |
|
Inside diameter (d) |
10 mm |
|
Outside diameter (D) |
22 mm |
|
Height (H) |
2.80 mm |
|
Dimensions |
10x22x2.80 mm |
|
Rolling elements |
Cylindrical needle rollers |
|
Load direction |
Axial, single-direction |
|
Primary function |
Transmission of axial forces |
The designation identifies the bearing series and its dimensional configuration.
AX - Axial needle roller bearing series. This is an important construction designation and must not be replaced with AXK.
1022 - Dimensional identification corresponding to a 10 mm inside diameter and 22 mm outside diameter.
ZEN - Bearing manufacturer and brand.
The nominal bearing height is 2.80 mm.
When identifying a replacement bearing, the inside diameter, outside diameter, overall height and construction of the raceway assembly must all be considered.
Bearings with identical nominal diameters are not necessarily interchangeable.
The AX series differs in construction from conventional AXK axial needle roller and cage assemblies.
In AX-series designs used by manufacturers such as NADELLA and JTEKT, the needle rollers operate within a cage arrangement incorporating a thin integrated raceway washer.
For ZEN AX1022, distributor specifications identify a pressed steel cage and supply as an individual needle roller assembly. However, a manufacturer-specific sectional drawing confirming the integrated washer construction has not been established.
Consequently, ZEN AX 1022 should not be described as a complete thrust bearing supplied with two separate raceway washers.
The pressed sheet-steel cage maintains the needle rollers at appropriate circumferential intervals and guides them during rotation.
The cylindrical needle rollers provide line contact with the mating raceway surfaces.
This geometry enables axial load transmission within a compact assembly with a low overall height.
Unlike axial ball bearings, the rolling elements are needle rollers rather than balls.
Correct operation depends on suitable raceway surfaces.
Where an integrated raceway washer is included, the opposite side still requires an appropriate mating raceway surface or a separately selected thrust washer.
The exact washer configuration of the ZEN version should be checked against the manufacturer's technical drawing before finalizing the installation design.
|
Feature |
ZEN AX 1022 |
AXK series |
|---|---|---|
|
Bearing type |
Axial needle roller bearing |
Axial needle roller and cage assembly |
|
Rolling elements |
Needle rollers |
Needle rollers |
|
Cage |
Pressed steel, according to ZEN distributor specifications |
Depends on manufacturer and version |
|
Raceway washer |
Integrated in typical AX-series construction |
Generally supplied separately |
|
Load direction |
Axial |
Axial |
|
Interchangeability |
Requires dimensional and construction verification |
Not automatically interchangeable |
The AX and AXK designations identify different product series.
The same nominal inside and outside diameters do not establish full mechanical interchangeability.
Differences in height, cage construction and raceway arrangement may affect installation requirements.
ZEN AX 1022 is intended to accommodate forces acting parallel to the shaft axis.
The needle rollers transfer axial loads between the cooperating raceway surfaces.
The load-carrying capability depends on the bearing's geometry, raceway condition, lubrication and operating conditions.
The exact basic dynamic and static load ratings must be obtained from manufacturer-specific technical data.
This bearing arrangement accommodates axial loading in one direction.
Where axial forces act alternately in opposite directions, an appropriate opposing bearing arrangement may be necessary.
The complete assembly must be designed to maintain correct alignment and load transmission.
ZEN AX 1022 is not designed to provide independent radial shaft support.
If radial and axial forces occur simultaneously, the machine must incorporate suitable radial bearing support.
An axial needle roller bearing should not be used as a direct substitute for a radial needle roller bearing.
The mating raceway surfaces are critical to the performance of an axial needle roller bearing.
They must provide sufficient hardness, dimensional accuracy and surface quality to withstand repeated rolling contact.
Where the machine component itself acts as a raceway, its material and heat treatment must be suitable for rolling contact.
An insufficiently hardened surface may suffer plastic deformation, indentation and premature fatigue.
Raceways should have an appropriate surface finish to support lubricant film formation and uniform load distribution.
Surface damage, corrosion, scoring or embedded contamination can accelerate bearing wear.
The cooperating raceway surfaces must be correctly aligned.
Angular misalignment can cause uneven loading across the needle rollers, increasing contact stress and reducing service life.
Where the machine does not provide a suitable raceway surface, a compatible thrust washer may be required.
The washer must be selected according to the actual bearing construction and mounting dimensions.
The needle rollers and mating raceways require effective lubrication to reduce friction, wear and surface damage.
Depending on the application, lubrication may be provided by oil or grease.
Selection should account for:
Axial load.
Rotational speed.
Operating temperature.
Lubricant viscosity.
Raceway surface condition.
Contamination exposure.
Lubricant compatibility with bearing materials.
Oil lubrication may be appropriate where the bearing operates within an oil-lubricated mechanical assembly.
The oil must reach the needle roller contact surfaces and maintain an adequate lubricating film.
Grease lubrication may be suitable for certain compact mechanisms where continuous oil circulation is unavailable.
The grease must be compatible with the bearing materials and operating conditions.
The AX designation does not specify a particular factory-applied lubricant.
|
Dimension |
Value |
|---|---|
|
Inside diameter (d) |
10 mm |
|
Outside diameter (D) |
22 mm |
|
Overall height (H) |
2.80 mm |
|
Diameter difference (D - d) |
12 mm |
|
Nominal radial cross-section |
6 mm |
The nominal radial cross-section is calculated as:
This value describes the radial space occupied by the bearing geometry and does not represent the thickness of an individual cage or raceway component.
The overall height of 2.80 mm is particularly important when selecting a replacement for an existing axial bearing arrangement.
The same ZEN product may be referenced using different spacing conventions:
ZEN AX 1022
ZEN AX1022
AX1022 ZEN
AX 1022 ZEN
AX1022ZEN
The designation NADELLA AX1022 10x22x2.8 mm also exists in industrial bearing catalogues.
However, identical nominal dimensions do not independently confirm complete interchangeability with the ZEN product.
The exact raceway arrangement and installation requirements must be compared.
Before selecting ZEN AX 1022, verify the following technical characteristics:
Complete designation: AX 1022.
Manufacturer: ZEN.
Series: AX, not AXK.
Inside diameter: 10 mm.
Outside diameter: 22 mm.
Overall height: 2.80 mm.
Rolling elements: Cylindrical needle rollers.
Cage: Pressed steel, according to distributor specifications.
Raceway configuration: Verify the integrated washer arrangement.
Load direction: Axial, single-direction.
Axial load capacity: Confirm against manufacturer data.
Rotational speed: Verify for the intended operating conditions.
Lubrication: Select according to the application.
Mating surfaces: Check hardness, flatness and surface finish.
Not without further verification.
Although both series are intended for axial load transmission, their construction and overall height may differ.
The replacement must be evaluated as part of the complete bearing arrangement rather than on nominal diameters alone.
Axial needle roller bearings of this type may be used in compact mechanical systems requiring axial load support.
Potential applications include:
Compact axial load-bearing mechanisms.
Gearbox assemblies.
Mechanical adjustment systems.
Shaft thrust arrangements.
Industrial machinery with limited axial installation space.
These are typical applications associated with this bearing type, not confirmed OEM applications for the specific ZEN AX1022 reference.
The actual operating conditions must be evaluated before installation.
Before installation, clean the mounting surfaces and inspect the needle rollers and mating raceways.
Remove any dirt, metal particles or foreign material that could damage the rolling contact surfaces.
Install the bearing without angular misalignment.
The mating raceways must be correctly positioned to distribute axial loads evenly across the needle rollers.
Avoid impacts, scratches and deformation of the needle rollers or raceway surfaces during handling.
Do not apply concentrated mounting forces directly to individual rolling elements.
Provide suitable lubrication before operation and maintain it according to the machine's service requirements.
Store the bearing in clean, dry conditions, protected against moisture, corrosion and mechanical damage.
ZEN AX 1022 is an axial needle roller bearing designed to accommodate axial loads acting in one direction.
The bearing measures 10x22x2.80 mm, with a 10 mm inside diameter, 22 mm outside diameter and 2.80 mm overall height.
No. AX and AXK identify different axial needle roller bearing series. They must not be treated as automatically interchangeable.
Distributor specifications identify a pressed sheet-steel cage.
The product is supplied as an individual axial needle roller bearing assembly rather than a complete arrangement with two separate thrust washers. The exact integrated washer construction of the ZEN version should be confirmed from the manufacturer's drawing.
It is not intended to provide independent radial shaft support. Its primary function is to accommodate axial loads.
The two products share the same basic designation and nominal dimensions, but their construction and raceway arrangements must be verified before substitution.
Yes. The needle rollers and mating raceways require suitable oil or grease lubrication according to the operating conditions.
ZEN AX 1022 is a single-direction axial needle roller bearing measuring 10x22x2.80 mm. It features cylindrical needle rollers and a pressed steel cage. The AX designation identifies a series distinct from AXK. The bearing transmits axial loads and requires suitable mating raceway surfaces. Its exact integrated washer configuration should be confirmed before installation.
The product is offered through the specialist B2B industrial supply platform simmering.pl, supporting industrial procurement with worldwide shipping from stock in Poland.
Data sheet