SKF 365208 40x80x24.75 mm - Spherical Plain Bearing

Technical Specifications

Dimensional verification: The listed dimensions are 40x80x24.75 mm. However, some references report different width values. The designation of 24.75 mm as dimension B or C has not been independently confirmed against an official SKF dimensional drawing.

The material combination, permissible angular misalignment, dynamic load rating, static load rating and lubrication requirements have not been verified for this exact product.

What Does SKF 365208 Mean?

The designation identifies a specific SKF bearing reference.

SKF is the manufacturer of the bearing.

365208 is the product designation used to identify the corresponding spherical plain bearing.

Unlike conventional SKF rolling bearing designations, the number 365208 does not contain explicitly identifiable suffixes such as 2RS, C3 or W33.

The individual digits should not be interpreted as a manufacturer-defined construction code without supporting SKF documentation.

The designation alone does not establish the sliding contact material, internal clearance, permissible tilting angle or lubrication method.

Construction and Operating Principle

SKF 365208 belongs to the spherical plain bearing category.

The basic construction consists of two cooperating components:

• Inner ring: Incorporates a convex spherical sliding surface.

• Outer ring: Incorporates a corresponding concave spherical sliding surface.

Relative movement occurs through sliding contact between the spherical surfaces rather than through rolling elements.

The spherical geometry allows angular displacement between the inner and outer rings within the limits permitted by the bearing construction.

This operating principle makes spherical plain bearings suitable for mechanical joints involving angular movement, oscillation or alignment changes.

The exact sliding material combination and permissible angular displacement for SKF 365208 have not been confirmed.

Radial and Angular Contact Spherical Plain Bearing Designs

Spherical plain bearings are available in different constructions depending on the direction and magnitude of the loads they are intended to accommodate.

A radial spherical plain bearing is primarily designed for radial loading, although certain designs can also accommodate axial loads.

An angular contact spherical plain bearing has a contact geometry intended to accommodate combined radial and axial loads.

Specialist distributor listings classify SKF 365208 as an angular contact spherical plain bearing.

This classification should be confirmed against the original SKF technical drawing before specifying load direction, load ratings or installation arrangements for a particular application.

Alternative Designations and Reference Formats

Natural reference formats include:

• SKF 365208

• 365208 SKF

• SKF365208

• SKF 365208 Spherical Plain Bearing

• SKF 365208 40x80x24.75 mm

Certain CNH parts references associate designation 365208 with the following numbers:

These references should not be treated as universally interchangeable without confirming the dimensional drawing, component version and machine compatibility.

Some related catalogue entries specify different widths.

SKF 365208 vs SKF 32208

Although both products may be associated with boundary dimensions of 40x80x24.75 mm, they represent fundamentally different bearing constructions.

SKF 32208 is a tapered roller bearing, while SKF 365208 is identified as a spherical plain bearing.

Identical or similar boundary dimensions do not make these bearings interchangeable.

Bearing Selection and Interchangeability

Before purchasing SKF 365208, verify the complete designation and the technical requirements of the intended assembly.

Important selection criteria include:

• Bore diameter of 40 mm.

• Outside diameter of 80 mm.

• Exact inner and outer ring widths.

• Spherical sliding surface geometry.

• Required radial and axial load capacity.

• Permissible angular displacement.

• Sliding material combination.

• Lubrication and maintenance requirements.

• Shaft and housing fits.

• Operating temperature and environmental conditions.

A replacement bearing must match not only the installation dimensions but also the operating characteristics of the original component.

For SKF 365208, confirmation of the dimensional drawing is particularly important because available catalogue sources are not fully consistent regarding width.

Applications of SKF 365208

Spherical plain bearings are used in mechanical assemblies that require load transmission combined with angular movement between connected components.

Typical applications for this bearing category include articulated mechanical joints, pivoting connections and assemblies subjected to oscillating movement.

The suitability of SKF 365208 for a particular application depends on its verified contact geometry, load capacity, sliding material and lubrication requirements.

Certain Case IH and New Holland parts catalogues associate the 365208 designation with agricultural equipment components.

However, compatibility with a specific machine must be confirmed using the manufacturer's parts catalogue, equipment model and serial number.

Installation and Operating Recommendations

Preparation

Before installation, clean the shaft, housing and bearing mounting surfaces.

Inspect the bearing for visible damage, corrosion and contamination.

Mounting

Apply installation forces to the ring being mounted with an interference fit.

Avoid transmitting mounting forces through the spherical sliding contact surfaces in a manner that could damage the bearing.

Use appropriate mounting tools and verify the required fits.

Lubrication

The exact sliding material combination and lubrication requirements have not been confirmed for SKF 365208.

Do not assume that the bearing is maintenance-free or requires a particular grease without verifying the manufacturer's specification.

Storage

Store the bearing in a clean, dry environment, preferably in its original packaging.

Protect the sliding surfaces against contamination, moisture, impacts and mechanical damage.

Frequently Asked Questions - FAQ

What are the dimensions of SKF 365208?

Available distributor listings specify a 40 mm bore, an 80 mm outside diameter and a listed width of 24.75 mm. Some catalogue references provide different width values, so the original dimensional drawing should be checked before installation.

Is SKF 365208 a rolling bearing?

No. SKF 365208 is identified as a spherical plain bearing. Its operating principle involves sliding contact between cooperating spherical surfaces rather than rolling elements.

Is SKF 365208 an angular contact spherical plain bearing?

Specialist distributor listings classify it as an angular contact spherical plain bearing. The exact contact geometry should be verified against SKF documentation before final engineering selection.

Does SKF 365208 have seals?

Available distributor information identifies it as an unsealed bearing.

Are SKF 365208 and SKF 32208 interchangeable?

No. SKF 365208 is a spherical plain bearing, while SKF 32208 is a tapered roller bearing. Their operating principles and mechanical functions differ.

Does SKF 365208 require lubrication?

The exact lubrication requirements have not been independently confirmed. They depend on the bearing's sliding material combination and operating conditions.

Is SKF 365208 equivalent to CNH part number 5119660?

Certain Case IH parts references associate designation 365208 with part number 5119660. Compatibility with a particular machine or component must be verified separately.

Can SKF 365208 accommodate angular movement?

Yes. Spherical plain bearing construction allows angular movement between the inner and outer rings. The permissible angular displacement for this exact bearing has not been confirmed.

SKF 365208 - Key Technical Information

SKF 365208 is a spherical plain bearing with a 40 mm bore, 80 mm outside diameter and listed width of 24.75 mm. It enables articulated movement through sliding contact between spherical surfaces. Before selection, verify the exact ring widths, contact geometry, load ratings, sliding materials and lubrication requirements against the manufacturer's documentation.

SKF 365208 at simmering.pl

SKF spherical plain bearings and other industrial bearing components are available through simmering.pl, a specialist supplier of rolling bearings, plain bearings, industrial seals and mechanical components.

We serve industrial companies, workshops, maintenance departments and technical purchasing teams.

Our warehouse and order processing facilities are located in Lublin, Poland. We provide worldwide shipping from stock in Poland.