NSK NJ2213ET 65x120x31 mm single-row cylindrical roller bearing, dimensional series 22. NJ design with two outer ring flanges and one inner ring flange. ET execution with modified internal geometry and PA66 polyamide cage. CN clearance, P0 tolerance class. Basic dynamic load rating 183 kN, static load rating 181 kN. Open, separable construction for radial and one-direction axial loads. Specialist B2B industrial trading platform simmering.pl, with worldwide shipping from stock in Poland.
|
Parameter |
Specification |
|---|---|
|
Manufacturer |
NSK |
|
Full designation |
NJ 2213 ET |
|
Bearing type |
Single-row cylindrical roller bearing |
|
Design |
NJ |
|
Dimensional series |
22 |
|
Inside diameter (d) |
65 mm |
|
Outside diameter (D) |
120 mm |
|
Width (B) |
31 mm |
|
Rolling elements |
Cylindrical rollers |
|
Number of rows |
1 |
|
Outer ring flanges |
2 |
|
Inner ring flanges |
1 |
|
Cage |
Polyamide, ET design |
|
Internal construction |
Modified, E design |
|
Separable construction |
Yes |
|
Sealing arrangement |
Open, without integrated seals |
|
Radial load capacity |
Yes |
|
Axial load capacity |
One direction |
|
Nominal dimensions |
65x120x31 mm |
The basic dynamic load rating C, basic static load rating C0, fatigue load limit, permissible speeds, bearing weight and operating temperature limits must be verified for the exact NSK NJ 2213 ET designation. These parameters must not be transferred from the NJ 2213 M version or from bearings manufactured by other companies.
|
Designation element |
Technical meaning |
|---|---|
|
N |
Cylindrical roller bearing |
|
NJ |
Two outer ring flanges and one inner ring flange |
|
22 |
Dimensional series |
|
13 |
Bore code corresponding to 65 mm |
|
E |
Modified NSK internal design |
|
T |
Plastic cage, polyamide in this execution |
|
NSK |
Bearing manufacturer |
An NJ-type bearing has two flanges on the outer ring and one flange on the inner ring.
This arrangement allows axial loads in one direction in addition to the primary radial loads.
The NJ design does not independently provide axial shaft location in both directions.
The designation 22 identifies the bearing's dimensional series.
For NJ 2213 ET, the nominal dimensions are:
d = 65 mm.
D = 120 mm.
B = 31 mm.
Bore code 13 corresponds to a nominal inside diameter of 65 mm.
13 x 5 = 65 mm.
The letter E identifies a modified internal bearing design used by NSK, associated with construction improvements intended to increase load-carrying capability.
It does not indicate a specific numerical dynamic load rating C. That value must be obtained from the catalogue data for the exact bearing version.
The letter T identifies a plastic cage design used in this NSK bearing family.
In the ET execution, the cage is manufactured from polyamide.
The cage's thermal and chemical properties must be considered when selecting the lubricant and evaluating operating conditions.
No. ET identifies the internal construction and cage design.
The NJ 2213 ET designation does not contain the C3 suffix, so increased radial internal clearance must not be assumed.
The official NSK product specification for the exact NJ2213ET designation confirms the following data:
|
Parameter |
Catalogue value |
|---|---|
|
Basic dynamic load rating (Cr) |
183 kN |
|
Basic static load rating (C0r) |
181 kN |
|
Thermal reference speed, oil bath |
6000 rpm |
|
Mechanical speed, circulating oil |
7100 rpm |
|
Limiting speed, grease lubrication |
4800 rpm |
|
Limiting speed, oil bath lubrication |
6000 rpm |
|
Approximate weight |
1.44 kg |
|
Radial internal clearance |
CN, normal |
|
Tolerance class |
P0 |
|
Cage material |
Polyamide 66 (PA66) |
|
Inner ring raceway diameter (Fw) |
78.5 mm |
|
Minimum chamfer dimensions (r and r1) |
1.5 mm |
The stated speeds correspond to specific NSK lubrication conditions. They are not guaranteed operating speeds for every bearing arrangement.
Natural designation variations include:
NSK NJ2213ET
NJ2213ET NSK
NJ 2213 ET NSK
NSK NJ 2213 ET
NJ2213ET 65x120x31
NSK NJ2213ET cylindrical roller bearing
NJ 2213 ET single-row cylindrical roller bearing
These are alternative ways of writing the same designation, not separate OEM reference numbers.
The outer ring has a diameter of 120 mm and two flanges that guide the cylindrical rollers.
These flanges provide axial guidance for the rolling elements and interact with their end faces.
The inner ring has a bore diameter of 65 mm and one flange.
This geometry allows the bearing to accommodate axial force in one direction.
The cylindrical rollers contact the raceways along an approximately linear contact zone.
This construction is particularly suitable for radial loading.
The E execution identifies modified internal geometry. The dynamic load rating for NJ2213ET is 183 kN.
NSK uses a polyamide 66 cage in this bearing execution.
The cage maintains appropriate spacing between the rollers and guides them during rotation.
When selecting the bearing, the compatibility of the cage material with operating temperature and lubricant must be considered.
The inner ring can be separated from the outer ring assembly containing the rollers and cage.
This facilitates installation, particularly when the shaft and housing require the bearing components to be mounted separately.
NJ2213ET is primarily designed to accommodate radial loads.
Its catalogue basic dynamic load rating Cr is 183 kN, while the basic static load rating C0r is 181 kN.
These values are used in bearing life calculations and load assessments according to the relevant calculation methods. They do not represent permissible continuous operating loads under all conditions.
The bearing can accommodate axial force in one direction.
Its axial load capacity is limited by factors including lubrication conditions and contact between the roller end faces and bearing ring flanges.
The value of 183 kN must not be interpreted as the permissible axial load capacity.
NSK specifies normal radial internal clearance CN for NJ2213ET.
Operating clearance may change due to bearing ring fits and temperature differences between the shaft and housing.
The CN execution should not be replaced with a C3 version without evaluating the required operating conditions.
|
Variant |
Main difference |
Selection significance |
|---|---|---|
|
NSK NJ2213ET |
NJ design, PA66 cage, CN clearance |
Accommodates axial loads in one direction |
|
NSK NJ2213ETC3 |
ET design, C3 clearance |
Greater radial internal clearance than CN |
|
NSK NU2213ET |
NU design |
Allows relative axial displacement in both directions |
|
NSK NUP2213ET |
NUP design |
Axial location in both directions, depending on execution |
These design variants may share nominal dimensions of 65x120x31 mm but differ in their axial function and operating characteristics.
The main difference is the radial internal clearance class.
NJ2213ET has catalogue-specified normal clearance CN, whereas the C3 designation indicates clearance greater than normal.
Changing the clearance class can affect operating temperature, rolling element loading and bearing service life.
An NJ bearing provides axial shaft location in one direction.
An NU bearing allows relative axial displacement between its rings in both directions.
These designs must not be interchanged solely because their dimensions match.
Before purchasing NSK NJ2213ET, verify:
Complete designation NJ2213ET.
Dimensions of 65x120x31 mm.
NJ construction.
PA66 cage.
CN radial internal clearance.
P0 tolerance class.
Basic dynamic load rating of 183 kN.
Basic static load rating of 181 kN.
Direction and magnitude of axial loads.
Rotational speed and lubrication method.
Bearing ring fits.
Operating temperature.
Required axial shaft support arrangement.
Identical dimensions do not guarantee complete technical interchangeability. The NJ design, internal clearance class and cage material are particularly important.
Single-row NJ cylindrical roller bearings are used in arrangements requiring substantial radial load capacity and axial shaft location in one direction.
Typical applications for this bearing family include industrial gearboxes, production machinery shafts, power transmission assemblies and bearing arrangements in industrial equipment.
These are characteristic applications of the NJ bearing family and do not establish confirmed applications of the exact NJ2213ET designation in specific machine models.
Shaft and housing surfaces must be clean and free from burrs and damage.
The required fits and condition of the supporting surfaces must be checked.
The separable design allows the bearing rings to be installed individually.
Mounting force must be applied directly to the ring being fitted with interference. It must not be transmitted through the rollers.
The bearing has an open construction and requires appropriate lubrication.
Under axial loading, lubrication of the contact surfaces between the roller ends and flanges is particularly important.
The PA66 cage requires consideration of operating temperature and compatibility with oil or grease.
The maximum operating temperature must not be determined solely from the permissible temperature of the steel bearing rings.
The bearing should remain in its original packaging until installation and be stored in a clean, dry environment.
The bearing has an inside diameter of 65 mm, an outside diameter of 120 mm and a width of 31 mm.
NJ identifies a design with two flanges on the outer ring and one flange on the inner ring. This arrangement allows axial loads in one direction.
E identifies a modified internal design, while T indicates a plastic cage. NSK confirms a polyamide 66 cage for this product.
According to NSK, the basic dynamic load rating Cr is 183 kN and the basic static load rating C0r is 181 kN.
The manufacturer specifies normal radial internal clearance CN. The C3 version is a separate execution.
NSK specifies 4800 rpm with grease lubrication, 6000 rpm with oil bath lubrication and 7100 rpm under suitable circulating oil conditions. The actual permissible speed depends on operating conditions.
Not automatically. The NJ design provides axial shaft location in one direction, whereas the NU design allows relative axial displacement in both directions.
No. The official NSK product specification identifies a polyamide 66 cage rather than a brass cage.
NSK NJ2213ET is a single-row cylindrical roller bearing measuring 65x120x31 mm, featuring an NJ design, a PA66 polyamide cage and normal CN internal clearance. It accommodates radial loads and axial loads in one direction. Its basic dynamic load rating is 183 kN and static load rating is 181 kN. The open, separable construction facilitates bearing ring installation.
The specialist B2B industrial trading platform simmering.pl supplies NSK bearings for industrial applications and maintenance operations, supporting component selection based on complete catalogue designations, dimensions and technical specifications, with worldwide shipping from stock in Poland.
Data sheet
You might also like