O-ring 11x2 NBR 70 Shore A - nitrile rubber sealing ring with an inside diameter of 11 mm and a cross-sectional diameter of 2 mm. Nominal outside diameter 15 mm. Manufactured from NBR elastomer with a hardness of 70 Shore A, offering good resistance to many mineral oils and lubricating greases. Suitable for appropriately designed static and selected dynamic sealing applications, including hydraulic and pneumatic systems. Pack of 100 pcs. Available through the specialist B2B industrial supply platform simmering.pl, with worldwide shipping from stock in Poland.
|
Parameter |
Specification |
|---|---|
|
Product designation |
O-ring 11x2 NBR 70 Shore A |
|
Product type |
Elastomeric O-ring seal |
|
Material |
NBR - nitrile butadiene rubber |
|
Inside diameter d1 |
11 mm |
|
Cross-sectional diameter d2 |
2 mm |
|
Nominal outside diameter |
15 mm |
|
Nominal hardness |
70 Shore A |
|
Cross-section |
Circular |
|
Sealing applications |
Static and selected dynamic applications |
|
Package quantity |
100 pcs. |
The nominal outside diameter of 15 mm is calculated from the dimensions 11x2 mm. Exact dimensional tolerances, NBR compound formulation and permissible operating conditions must be confirmed in the technical documentation for the specific product.
The dimensional designation specifies:
11 mm - nominal inside diameter.
2 mm - nominal cross-sectional diameter.
15 mm - calculated nominal outside diameter.
The outside diameter is calculated using the following formula:
For O-rings, the designation 11x2 refers to the inside diameter and cross-sectional diameter, rather than the shaft diameter and axial width used for conventional rotary shaft oil seals.
NBR is a synthetic elastomer widely used in industrial sealing applications.
Its characteristic properties include:
Good resistance to many mineral oils.
Compatibility with numerous industrial lubricating greases.
Elasticity suitable for sealing mechanical connections.
Suitability for many hydraulic and pneumatic applications.
Use in static and selected dynamic sealing systems.
The chemical resistance of NBR depends on the rubber compound, operating medium and service conditions.
NBR is not a universal sealing material and may be unsuitable for certain solvents, specific fuel formulations, ozone exposure and prolonged outdoor weathering.
The designation 70 Shore A indicates the nominal hardness of the elastomer.
Hardness influences:
Material compressibility.
Contact pressure within the sealing groove.
Behaviour under changing pressure.
Resistance to extrusion into a clearance gap.
Conformity to mating surfaces.
A hardness of 70 Shore A is commonly used in standard industrial sealing applications. However, hardness alone does not establish the permissible operating pressure.
The O-ring 11x2 NBR 70 Shore A is a continuous elastomeric ring with a circular cross-section.
When installed in a correctly designed groove, the ring is compressed between the mating surfaces.
The resulting material deformation generates sealing contact pressure, restricting the passage of liquids or gases through the connection.
In static connections, the O-ring operates between components that do not move relative to each other during normal operation.
Typical configurations include:
Equipment covers.
Flanged connections.
Valve bodies.
Pump housings.
Hydraulic fittings with suitable sealing grooves.
NBR O-rings may also be used in appropriately designed systems involving relative movement.
Such applications require consideration of:
Movement speed.
Friction.
Lubrication.
Operating pressure.
Surface roughness.
Groove dimensions.
Elastomer wear resistance.
Not every O-ring designed for static sealing is suitable for dynamic operation.
Nitrile rubber is frequently selected for sealing systems operating with mineral oils and industrial lubricating greases.
Its resistance depends on the specific composition of the operating medium and the temperature.
In many industrial applications, standard NBR compounds have an approximate operating temperature range of -30°C to +100°C.
Specialised compounds may have different operating limits.
Important: This temperature range is a general characteristic of NBR material, not a verified temperature specification for this particular O-ring.
NBR provides mechanical properties suitable for many industrial sealing applications.
Actual abrasion resistance, compression set and tear resistance depend on the compound formulation and operating conditions.
NBR O-rings are used in numerous industrial sectors.
Typical applications include:
Hydraulic installations.
Pneumatic systems.
Valves and control distributors.
Industrial pumps.
Technical fittings and adapters.
Threaded connections with sealing grooves.
Mechanical equipment housings.
Lubrication system components.
Industrial machinery and technical equipment.
These are typical applications of NBR material. Compatibility of the exact 11x2 mm dimensions with a particular assembly must be verified.
|
Parameter |
NBR 70 Shore A |
NBR 90 Shore A |
FKM 70 Shore A |
|---|---|---|---|
|
Material |
Nitrile rubber |
Nitrile rubber |
Fluoroelastomer |
|
Hardness |
70 Shore A |
90 Shore A |
70 Shore A |
|
Compressibility |
Greater than NBR 90 |
Lower than NBR 70 |
Compound-dependent |
|
Resistance to many mineral oils |
Good |
Good |
Generally good |
|
Extrusion resistance |
Depends on conditions |
Generally higher with the same geometry |
Depends on compound and hardness |
|
High-temperature resistance |
Limited by NBR properties |
Limited by NBR properties |
Generally higher |
|
Typical applications |
Standard industrial seals |
Systems requiring harder elastomers |
Applications requiring different chemical or temperature resistance |
Material selection should be based on actual operating conditions rather than sealing ring dimensions alone.
|
Parameter |
O-ring 11x2 |
O-ring 11x2.5 |
|---|---|---|
|
Inside diameter |
11 mm |
11 mm |
|
Cross-sectional diameter |
2 mm |
2.5 mm |
|
Nominal outside diameter |
15 mm |
16 mm |
|
Cross-section difference |
— |
+0.5 mm |
|
Interchangeability |
Requires verification |
Requires verification |
A difference of 0.5 mm in cross-sectional diameter can significantly change the compression of the ring inside the sealing groove.
O-ring 11x2 NBR 70 Shore A should not automatically be replaced with O-ring 11x2.5 NBR 70 Shore A.
Before purchasing, verify:
Inside diameter of 11 mm.
Cross-sectional diameter of 2 mm.
NBR material.
Hardness of 70 Shore A.
Sealing groove dimensions.
Type of operating medium.
Operating temperature and pressure.
Static or dynamic sealing conditions.
Required dimensional tolerances.
Any material or certification requirements.
Identical dimensions do not guarantee complete interchangeability between sealing rings manufactured from different elastomers.
Thoroughly clean the sealing groove.
Remove burrs and sharp edges.
Inspect the mating surfaces.
Avoid excessive stretching.
Prevent twisting during installation.
Use an NBR-compatible assembly lubricant where required.
Do not install damaged or permanently deformed rings.
NBR O-rings should be stored in a clean, dry environment, protected from direct sunlight, heat sources and ozone.
Proper storage helps preserve the elastomer's mechanical and sealing properties.
O-ring 11x2 NBR 70 Shore A
NBR O-ring 11x2 mm 70 Shore A
O-ring 11x2 mm NBR 70
NBR Sealing Ring 11x2
Rubber O-ring Seal 11x2 mm
NBR 70 O-ring 11x2 mm
Nitrile Rubber O-ring 11x2 mm
These are technical naming variations, not verified catalogue numbers or OEM references.
The inside diameter is 11 mm and the cross-sectional diameter is 2 mm. The nominal outside diameter is 15 mm.
NBR stands for nitrile butadiene rubber, a synthetic elastomer used in oil sealing, hydraulic and pneumatic applications.
It indicates the nominal elastomer hardness of 70 units on the Shore A scale.
NBR offers good resistance to many mineral oils and industrial lubricating greases. Exact compatibility depends on the operating medium and temperature.
Yes, provided that groove design, operating pressure, material compatibility and service conditions are suitable.
Interchangeability should not be assumed. The difference in cross-sectional diameter affects compression and sealing performance.
The permissible temperature depends on the rubber compound and operating medium. NBR generally has more limited high-temperature resistance than certain other elastomers.
Each package contains 100 pieces of O-ring 11x2 NBR 70 Shore A.
O-ring 11x2 NBR 70 Shore A is an elastomeric sealing ring with an inside diameter of 11 mm and a cross-sectional diameter of 2 mm, manufactured from nitrile rubber with a hardness of 70 Shore A. NBR provides good resistance to many mineral oils and greases. The product is suitable for appropriately designed static and selected dynamic sealing applications. Supplied in packs of 100 pieces.
Available through the specialist B2B industrial supply platform simmering.pl, with worldwide shipping from stock in Poland.
You might also like