|
Parameter |
Specification |
|---|---|
|
Product designation |
O-ring NBR 11x2 mm 70 Shore A - 1000 pcs. |
|
Product type |
Elastomeric O-ring seal |
|
Material |
NBR - nitrile butadiene rubber |
|
Inside diameter d1 |
11 mm |
|
Cross-sectional diameter d2 |
2 mm |
|
Nominal outside diameter |
15 mm |
|
Nominal hardness |
70 Shore A |
|
Cross-section |
Circular |
|
Sealing applications |
Static and selected dynamic applications |
|
Package quantity |
1000 pcs. |
|
Sales unit |
Bulk package |
The nominal outside diameter of 15 mm is calculated from the inside diameter and cross-sectional diameter. Exact dimensional tolerances, NBR compound formulation and permissible operating conditions must be confirmed in the technical documentation for the specific product.
NBR, also known as nitrile rubber, is a synthetic elastomer widely used in industrial sealing applications.
Its characteristic properties include:
Good resistance to many mineral oils.
Compatibility with numerous industrial lubricating greases.
Elasticity that allows conformity to sealing surfaces.
Suitability for appropriately designed hydraulic systems.
Use in pneumatic installations.
Good performance in many static sealing connections.
Chemical resistance depends on the elastomer compound formulation, operating temperature and type of sealed medium.
NBR is not universally resistant to all chemical substances. Particular attention should be paid to compatibility with certain solvents, ozone and outdoor environmental conditions.
The designation 11x2 mm specifies:
11 mm - nominal inside diameter.
2 mm - nominal cross-sectional diameter.
15 mm - calculated nominal outside diameter.
The outside diameter is calculated as follows:
O-ring dimensions are specified using the inside diameter and cross-sectional diameter. Correct identification of both measurements is essential when selecting a replacement.
A hardness of 70 Shore A indicates the nominal hardness of the elastomer measured on the Shore A scale.
This parameter influences:
Deformability of the sealing ring.
Force required for compression.
Contact pressure against mating surfaces.
Behaviour under operating pressure.
Resistance to extrusion into the installation clearance.
A hardness of 70 Shore A is commonly used in standard industrial sealing rings. However, it does not independently establish a permissible operating pressure.
The product is supplied in a bulk package containing 1000 O-rings with the same nominal dimensions and material designation.
Bulk packaging is particularly suitable for professional applications involving regular demand for sealing components.
The O-ring NBR 11x2 mm is a continuous elastomeric ring with a circular cross-section.
When installed in a correctly designed sealing groove, it undergoes controlled compression between the mating surfaces.
The resulting material deformation generates contact pressure that restricts the passage of liquids or gases through the connection.
In static applications, the O-ring operates between components that remain stationary relative to each other.
Typical configurations include:
Flanged connections.
Equipment covers and housings.
Valve bodies.
Technical fittings.
Hydraulic system components.
NBR O-rings may also be used in selected dynamic applications.
Such applications require consideration of movement speed, friction, lubrication, surface roughness and pressure conditions.
Not every O-ring designed for static connections is suitable for rotary or reciprocating movement.
NBR is one of the commonly used elastomers for sealing systems operating with mineral oils and lubricating greases.
Appropriate material selection depends on the specific oil formulation, chemical additives and operating temperature.
In many industrial applications, standard NBR compounds have an approximate operating temperature range of -30°C to +100°C.
Specialised compounds may have different operating limits.
Important: This is a general characteristic of the NBR material family, not a verified temperature range for this particular product.
NBR provides mechanical characteristics suitable for many industrial sealing applications.
Abrasion resistance, compression set and tear resistance depend on the specific compound and operating conditions.
NBR sealing rings are used across numerous industrial sectors.
Typical applications include:
Hydraulic power systems.
Pneumatic installations.
Industrial pumps and valves.
Hydraulic control distributors.
Technical fittings and adapters.
Lubrication system components.
Machinery housings.
Mechanical equipment.
Maintenance and servicing operations.
Industrial component assembly.
These are typical applications of NBR sealing rings, not confirmed equipment-specific applications of the exact 11x2 mm dimensions.
|
Feature |
NBR 70 Shore A |
NBR 90 Shore A |
FKM 70 Shore A |
|---|---|---|---|
|
Material |
Nitrile rubber |
Nitrile rubber |
Fluoroelastomer |
|
Hardness |
70 Shore A |
90 Shore A |
70 Shore A |
|
Compressibility |
Greater than NBR 90 |
Lower than NBR 70 |
Compound-dependent |
|
Resistance to many mineral oils |
Good |
Good |
Generally good |
|
Extrusion resistance |
Depends on conditions |
Generally higher with identical geometry |
Compound-dependent |
|
Elevated-temperature resistance |
Limited by NBR properties |
Limited by NBR properties |
Generally higher |
|
Typical applications |
Standard industrial sealing |
Systems requiring harder elastomers |
Applications with different chemical and thermal requirements |
Elastomer selection should be based on actual operating conditions and engineering requirements.
|
Parameter |
O-ring 11x2 mm |
O-ring 11x2.5 mm |
|---|---|---|
|
Inside diameter |
11 mm |
11 mm |
|
Cross-sectional diameter |
2 mm |
2.5 mm |
|
Nominal outside diameter |
15 mm |
16 mm |
|
Cross-section difference |
— |
+0.5 mm |
|
Interchangeability |
Requires verification |
Requires verification |
A difference of 0.5 mm in cross-sectional diameter can significantly affect compression inside the sealing groove.
O-ring 11x2 mm should not automatically be replaced with an 11x2.5 mm ring, even when both products are manufactured from NBR with a hardness of 70 Shore A.
Before purchasing, verify:
Inside diameter of 11 mm.
Cross-sectional diameter of 2 mm.
NBR material.
Hardness of 70 Shore A.
Sealing groove dimensions.
Required compression level.
Type of sealed medium.
Operating temperature and pressure.
Static or dynamic sealing conditions.
Required dimensional tolerances and material documentation.
Sealing rings with identical dimensions but different elastomer materials are not necessarily interchangeable.
Thoroughly clean the sealing groove.
Remove burrs and sharp edges.
Inspect the mating surfaces.
Avoid excessive stretching.
Prevent twisting during installation.
Use compatible assembly lubricants where required.
Do not install damaged or permanently deformed sealing rings.
The package containing 1000 pieces should be stored in a clean, dry environment, protecting the rings from direct sunlight, excessive heat and ozone.
For long-term storage, appropriate elastomer storage practices should be followed.
O-ring NBR 11x2 mm 70 Shore A - 1000 pcs.
O-ring 11x2 NBR 70 Shore A
NBR O-ring 11x2 mm 70 Shore A
Nitrile Rubber O-ring 11x2 mm
NBR Sealing Ring 11x2
Rubber O-ring Seal 11x2 mm
NBR 70 O-ring 11x2 mm
O-ring 11x2 NBR 70 - 1000 pcs. pack
These are naming variations, not verified OEM references or manufacturer catalogue numbers.
The inside diameter is 11 mm and the cross-sectional diameter is 2 mm. The nominal outside diameter is 15 mm.
NBR stands for nitrile butadiene rubber, a synthetic elastomer used in sealing applications involving mineral oils and lubricating greases.
It indicates the nominal elastomer hardness of 70 units on the Shore A scale.
NBR offers good resistance to many mineral oils and industrial lubricating greases. Compatibility must be confirmed for the specific operating medium.
Yes, in appropriately designed systems after verifying operating pressure, groove geometry, installation clearance and material compatibility.
Interchangeability should not be assumed. The difference in cross-sectional diameter affects compression and sealing performance.
Bulk packaging is convenient for manufacturing companies, maintenance departments, workshops and industrial service providers that regularly use O-rings of this size.
Each package contains 1000 pieces of O-ring NBR 11x2 mm 70 Shore A.
O-ring NBR 11x2 mm 70 Shore A is an elastomeric sealing ring with an inside diameter of 11 mm and a cross-sectional diameter of 2 mm, manufactured from nitrile rubber with a nominal hardness of 70 Shore A. The material provides good resistance to many mineral oils and greases. Suitable for appropriately designed static and selected dynamic sealing applications. Supplied in packs of 1000 pieces.
Available through the specialist B2B industrial supply platform simmering.pl, with worldwide shipping from stock in Poland.
You might also like