Simrit 80x100x10 BAUSL Simmerring - double-lip radial shaft oil seal with dimensions of 80x100x10 mm. The BAUSL profile features a spring-loaded primary sealing lip, an additional dust lip and a rubber-covered outer surface. Designed for sealing rotating shafts in appropriately selected mechanical systems, gearboxes and industrial machinery. Available through the specialist B2B industrial supply platform simmering.pl, with worldwide shipping from stock in Poland.
|
Parameter |
Specification |
|---|---|
|
Manufacturer / Brand |
Simrit / Freudenberg |
|
Product designation |
Simrit 80x100x10 BAUSL Simmerring |
|
Product type |
Radial shaft oil seal |
|
Inside diameter d1 |
80 mm |
|
Outside diameter d2 |
100 mm |
|
Width b |
10 mm |
|
Design profile |
BAUSL |
|
Number of lips |
Two: primary sealing lip and dust lip |
|
Primary sealing lip |
Spring-loaded |
|
Additional dust lip |
Yes |
|
Outer surface |
Rubber-covered |
|
Structural reinforcement |
Metal insert |
|
Material |
NBR in standard catalogue BA.../SL versions; verify for the specific product |
|
Application |
Sealing rotating shafts |
Freudenberg technical catalogues describe the BA.../SL design family, including BAUSL profiles. Different versions of 80x100x10 shaft seals may exist. Therefore, the exact elastomer material, manufacturer article number and design variant should be verified using the markings or technical documentation of the specific product.
Simrit is a brand associated with Freudenberg sealing solutions.
The name Simmerring is commonly used for radial shaft seals designed to prevent lubricant leakage around rotating shafts.
These seals separate the lubricated interior of mechanical equipment from the surrounding environment while maintaining sealing performance during shaft rotation.
The dimensional designation specifies:
80 mm - nominal shaft diameter.
100 mm - nominal housing bore diameter.
10 mm - nominal axial width of the seal.
All three dimensions must correspond to the installation requirements of the equipment.
The BAUSL profile belongs to a family of radial shaft seals featuring a rubber-covered outer diameter, a spring-loaded primary sealing lip and an additional dust lip.
This construction provides:
Dynamic sealing of rotating shafts.
Contact pressure supported by a garter spring.
Additional protection against moderate dust and contamination.
Static sealing between the outer surface of the seal and the housing bore.
A rubber-covered outer surface that helps accommodate minor housing surface irregularities.
The design is described in Freudenberg technical documentation for the BA.../SL sealing family.
The primary sealing lip operates in direct contact with the rotating shaft surface.
Its purpose is to restrict the escape of oil or another compatible lubricant from the equipment.
The garter spring helps maintain appropriate contact pressure between the primary sealing lip and the shaft.
This is important for maintaining sealing contact during equipment operation.
The dust lip provides an additional barrier against external dirt and contamination.
However, it does not automatically guarantee protection against pressurised water or severe abrasive contamination.
The elastomer-covered outer surface helps create a tight static seal between the sealing ring and the housing bore.
This construction is particularly useful where reliable sealing at the housing interface is required.
Standard NBR versions of the BA.../SL sealing family use nitrile butadiene rubber, which provides good resistance to many mineral oils and lubricating greases.
Typical NBR properties include:
Good resistance to numerous lubricating oils.
Suitability for many industrial drive systems.
Elasticity required for effective sealing lip operation.
Mechanical properties appropriate for many rotary sealing applications.
For standard NBR compounds, an approximate operating temperature range of -30°C to +100°C is commonly used as general material guidance.
Important: This is not a verified operating temperature range for the specific Simrit 80x100x10 BAUSL seal.
Permissible operating temperature also depends on shaft speed, friction, lubrication and the actual temperature at the sealing lip contact area.
Radial shaft seals from the BA.../SL family are used in numerous industrial machines and mechanical systems with rotating shafts.
Typical applications include:
Industrial gearboxes.
Mechanical speed reducers.
Drive shafts.
Agricultural machinery.
Construction machinery.
Power tools and mechanical drive equipment.
Oil-lubricated mechanisms.
Mechanical assemblies requiring radial shaft sealing.
These are typical applications of the BA.../SL design family, not confirmed equipment-specific applications of the exact 80x100x10 dimensions.
|
Feature |
BA |
BAUSL |
BAUSLX2 |
|---|---|---|---|
|
Outer surface |
Rubber-covered |
Rubber-covered |
Rubber-covered |
|
Primary sealing lip |
Yes |
Yes |
Yes |
|
Garter spring |
Yes |
Yes |
Yes |
|
Additional dust lip |
No |
Yes |
Yes |
|
Lip design |
Standard BA |
BAU with additional dust lip |
X2 profile with additional dust lip |
|
Main application |
Shaft sealing |
Shaft sealing with dust protection |
Shaft sealing with dust protection |
These profiles belong to the Freudenberg radial shaft sealing range but differ in their detailed construction.
They should not automatically be considered fully interchangeable.
BAUSL and AO/TC profiles share a similar general operating principle: a spring-loaded primary sealing lip and an additional dust lip.
However, this does not guarantee complete interchangeability.
|
Parameter |
Simrit BAUSL |
AO/TC Type |
|---|---|---|
|
Product type |
Radial shaft oil seal |
Radial shaft oil seal |
|
Primary sealing lip |
Spring-loaded |
Usually spring-loaded |
|
Dust lip |
Yes |
Yes |
|
Outer surface |
Rubber-covered |
Usually rubber-covered |
|
Detailed lip geometry |
According to Freudenberg profile |
Manufacturer-dependent |
|
Interchangeability |
Requires verification |
Requires verification |
When selecting a replacement, dimensions alone are insufficient.
The elastomer material, sealing lip geometry, installation requirements and operating conditions must also be checked.
Before purchasing, verify:
Shaft diameter of 80 mm.
Housing bore diameter of 100 mm.
Seal width of 10 mm.
BAUSL design profile.
Elastomer material.
Type of sealed medium.
Operating temperature.
Shaft rotational speed.
Operating pressure conditions.
Condition of the shaft and housing surfaces.
Important: Matching dimensions of 80x100x10 do not guarantee interchangeability between seals with different profiles.
Correct installation significantly influences the service life and sealing performance of a radial shaft oil seal.
Recommended installation practices include:
Thoroughly clean the shaft and housing bore.
Check the shaft for burrs, scratches and surface damage.
Protect the sealing lip from cuts when sliding the seal over the shaft.
Use an appropriate installation tool to apply even pressure.
Avoid tilting or misaligning the seal.
Provide suitable lubrication of the primary sealing lip during installation.
Maintain the correct installation orientation relative to the sealed medium.
Follow the equipment manufacturer's installation instructions.
In typical applications, the spring-loaded primary sealing lip faces the sealed medium, while the additional dust lip faces the external environment.
Special equipment designs may require a different arrangement, so the equipment documentation should always take priority.
The seal has an inside diameter of 80 mm, an outside diameter of 100 mm and a width of 10 mm.
BAUSL identifies a radial shaft seal profile with a rubber-covered outer surface, a spring-loaded primary sealing lip and an additional dust lip.
Yes. The BAUSL design includes a primary sealing lip and an additional dust lip.
BAUSL seals manufactured from suitable NBR compounds can be used with many mineral oils. Compatibility with the specific operating medium must be verified.
Replacement may be possible in certain applications, but the elastomer material, lip geometry, dimensions and operating conditions must be checked.
The additional dust lip helps restrict the entry of contamination but does not automatically provide protection against pressurised water.
Standard BA.../SL designs may operate in either rotational direction when no special directional sealing geometry is used. The exact seal version should be confirmed.
Permissible operating pressure depends on the specific seal design and operating conditions. Suitability for elevated pressure should not be assumed solely from the BAUSL designation.
Simrit 80x100x10 BAUSL Simmerring
Simrit BAUSL 80x100x10
Simmerring 80x100x10 BAUSL
Simrit 80x100x10 Radial Shaft Seal
Double-Lip Oil Seal 80x100x10
Radial Shaft Seal 80x100x10 BAUSL
Freudenberg Simrit 80x100x10
Wellendichtring 80x100x10 BAUSL
These are technical naming variations, not verified OEM references or manufacturer catalogue numbers.
Simrit 80x100x10 BAUSL Simmerring is a radial shaft oil seal with an inside diameter of 80 mm, an outside diameter of 100 mm and a width of 10 mm. The BAUSL profile features a spring-loaded primary sealing lip, an additional dust lip and a rubber-covered outer surface. Its construction helps prevent lubricant leakage and restrict contamination entering the sealing area.
Available through the specialist B2B industrial supply platform simmering.pl, with worldwide shipping from stock in Poland.
Data sheet
You might also like