ZVL 608 ZZ 8x22x7 mm single-row deep groove ball bearing from the Slovak-origin ZVL brand. Two non-contact metal shields (ZZ), normal CN radial internal clearance and non-separable construction. Accommodates radial and bidirectional axial loads. Replacement selection requires verification of the complete designation, manufacturer load ratings and limiting speeds. Specialist B2B industrial trading platform simmering.pl, with worldwide shipping from stock in Poland.
|
Parameter |
Specification |
|---|---|
|
Brand |
ZVL |
|
Brand origin |
Slovakia |
|
Product designation |
608 ZZ |
|
Compact designation |
608ZZ |
|
Bearing type |
Deep groove ball bearing |
|
Construction |
Single-row |
|
Bearing series |
608 |
|
Inside diameter (d) |
8 mm |
|
Outside diameter (D) |
22 mm |
|
Width (B) |
7 mm |
|
Rolling elements |
Balls |
|
Number of rows |
1 |
|
Shields |
Two metal shields, ZZ |
|
Shield design |
Non-contact |
|
Radial internal clearance |
Normal, CN |
|
Separable construction |
No |
|
Radial load capacity |
Yes |
|
Axial load capacity |
Both directions |
|
Nominal dimensions |
8x22x7 mm |
The dimensions and construction characteristics follow from the 608 ZZ designation. Exact values for load ratings, limiting speeds, weight and cage construction must be established from the manufacturer's documentation for the specific ZVL 608ZZ execution.
These parameters must not be copied from SKF, FAG, SNR or other manufacturers' bearings.
|
Designation element |
Technical meaning |
|---|---|
|
6 |
Deep groove ball bearing |
|
608 |
Bearing series with an 8 mm bore |
|
ZZ |
Two metal shields |
|
No C3 suffix |
Normal radial internal clearance |
|
ZVL |
Bearing brand originating in Slovakia |
The 608 designation identifies a small deep groove ball bearing with the following nominal dimensions:
Bore diameter: 8 mm.
Outside diameter: 22 mm.
Width: 7 mm.
For the 608 series, the bore diameter is directly identified as 8 mm.
The rule of multiplying the last two digits of the designation by five, which applies to many larger bearings, does not apply to this size.
The ZZ suffix indicates two metal shields positioned on opposite sides of the bearing.
The shields form a barrier that limits the entry of larger contaminants into the raceways and rolling elements while helping retain grease inside the bearing.
Unlike contact seals, they do not operate in continuous frictional contact with the inner ring.
Consequently, the additional rotational resistance generated by the shields is relatively low.
ZZ shields do not provide waterproof protection. They should not be considered equivalent to rubber contact seals in applications exposed to water, heavy dust contamination or pressurized liquids.
The 608 ZZ designation does not contain an additional suffix specifying increased clearance, such as C3.
The standard execution corresponds to normal CN radial internal clearance.
This clearance is specified before installation and may decrease when the bearing is mounted on the shaft and in the housing.
The final operating clearance is primarily influenced by bearing ring fits and temperature differences during operation.
The inner ring has a nominal bore diameter of 8 mm.
It is mounted on the shaft, and its raceway provides one of the rolling contact surfaces for the balls.
With an interference fit, the inner ring may expand slightly, reducing radial internal clearance.
The outer ring has a nominal outside diameter of 22 mm.
Its raceway works with the balls, while its outside cylindrical surface is used to locate the bearing in the housing.
The single-row ball arrangement is primarily designed to accommodate radial loads.
The raceway geometry of a deep groove ball bearing also allows axial loads to be supported in both directions.
The actual axial load capacity depends on radial loading, operating clearance and application conditions.
The cage maintains appropriate spacing between the balls and reduces direct contact between adjacent rolling elements.
The cage material for the exact ZVL 608ZZ execution requires confirmation from the manufacturer's catalogue.
A pressed steel cage must not be assumed simply because it is used in 608ZZ bearings from other manufacturers.
The two metal shields reduce the entry of contaminants and help retain lubricant within the bearing.
The shields are not intended to be removed during normal operation.
Deformation may cause contact with bearing components and increase rotational resistance.
The 608 ZZ bearing is primarily designed to accommodate radial loads.
The basic dynamic load rating C is used to calculate nominal bearing fatigue life.
For ball bearings, the basic rating life equation is:
Where:
L10 - basic rating life in millions of revolutions.
C - basic dynamic load rating.
P - equivalent dynamic bearing load.
Calculations must use the C value specified by ZVL for the exact 608ZZ execution.
The deep groove ball bearing construction allows axial loads to be supported in both directions.
However, this does not mean that the permissible axial load equals the radial load rating.
When radial and axial loads act simultaneously, the equivalent dynamic bearing load must be calculated using the appropriate bearing calculation method.
The basic static load rating C0 is relevant when assessing loads acting on a stationary bearing or one rotating very slowly.
It is used to evaluate the risk of permanent deformation at the contact points between the balls and raceways.
The numerical C0 value must be obtained from ZVL manufacturer's documentation.
Non-contact metal shields do not generate continuous sealing friction against the inner ring.
This is beneficial in applications involving higher rotational speeds.
However, it does not mean that every 608ZZ bearing has the same limiting speed.
Permissible speed depends on cage construction, lubricant, loading, temperature and mounting conditions.
Natural product designation variations include:
ZVL 608 ZZ
608 ZZ ZVL
ZVL 608ZZ
608ZZ ZVL
608-ZZ ZVL
ZVL 608 ZZ 8x22x7
ZVL 608ZZ deep groove ball bearing
These are commercial notation variations of the same bearing designation.
They do not represent confirmed OEM reference numbers or separate catalogue executions.
|
Bearing variant |
Protection |
Clearance |
Main difference |
|---|---|---|---|
|
608 |
No shields |
Normal unless otherwise specified |
Open construction |
|
608 ZZ |
Two metal shields |
Normal |
Non-contact contamination protection |
|
608 ZZ C3 |
Two metal shields |
C3 |
Increased radial internal clearance |
|
608 2RS |
Two contact seals |
Normal unless otherwise specified |
Improved contamination protection |
|
608 2RS C3 |
Two contact seals |
C3 |
Contact seals and increased clearance |
This table explains the differences between common construction variants of the 608 series. It does not confirm that every listed variant is currently available from ZVL.
Both executions have the same nominal dimensions and two metal shields.
The difference concerns radial internal clearance:
608 ZZ - normal CN clearance.
608 ZZ C3 - clearance greater than normal.
The C3 variant may be required in assemblies where bearing fits or thermal conditions significantly reduce operating clearance.
However, C3 should not automatically be substituted for CN.
The ZZ execution uses non-contact metal shields.
The 2RS designation commonly identifies two contact seals that provide more effective protection against contamination.
Contact seals, however, generate additional friction.
The exact sealing suffix used by the manufacturer must be confirmed when selecting a replacement.
|
Feature |
ZVL 608ZZ |
SKF 608-2Z |
FAG 608-2Z |
SNR 608ZZ |
|---|---|---|---|---|
|
Brand |
ZVL |
SKF |
FAG |
SNR |
|
Dimensions |
8x22x7 mm |
8x22x7 mm |
8x22x7 mm |
8x22x7 mm |
|
Bearing type |
Deep groove |
Deep groove |
Deep groove |
Deep groove |
|
Shields |
Two metal |
Two metal |
Two metal |
Two metal |
|
Standard clearance |
CN |
CN |
CN |
CN |
|
Catalogue load ratings |
According to ZVL |
According to SKF |
According to FAG |
According to SNR |
|
Catalogue speeds |
According to ZVL |
According to SKF |
According to FAG |
According to SNR |
All listed designations refer to the same basic dimensional bearing size.
Matching dimensions do not automatically mean identical operating specifications.
Before substitution, compare complete designations, load ratings, limiting speeds, shield construction and the requirements of the particular application.
Before purchasing, verify:
Complete designation ZVL 608 ZZ.
Shaft diameter of 8 mm.
Housing bore diameter of 22 mm.
Available installation width of 7 mm.
ZZ metal shield construction.
Required radial internal clearance class.
Radial and axial loads.
Rotational speed.
Bearing ring fits.
Operating temperature.
Lubrication conditions.
Dust contamination and moisture exposure.
Distinguishing between CN and C3 clearance is particularly important.
Using a bearing with inappropriate internal clearance may result in increased friction, higher operating temperatures, noise or incorrect shaft guidance.
Deep groove ball bearings in the 608 series are commonly used in small rotating mechanisms.
Typical applications of this construction include:
Small electric motors.
Fans.
Guide rollers.
Small conveyor assemblies.
Compact drive mechanisms.
Workshop equipment.
Auxiliary machine mechanisms.
The ZZ execution is suitable where basic contamination protection is required without the additional friction associated with contact seals.
These examples relate to the general 608ZZ bearing design and do not represent confirmed OEM applications for the specific ZVL product.
Before installation, clean the shaft, housing bore and supporting shoulders.
Burrs or contamination may prevent correct seating of the bearing rings.
When the inner ring is installed with an interference fit, mounting force must be applied directly to that ring.
Force must not be transmitted through the balls, as this may damage the raceways.
When the outer ring is installed with an interference fit, mounting force must be applied directly to the outer ring.
If both rings are simultaneously installed with interference fits, an appropriate mounting tool supporting both rings is required.
Metal shields must not be deformed or pried off during installation.
A damaged shield may rub against a bearing ring and increase rotational resistance.
Bearings with metal shields on both sides are generally supplied with grease.
The exact lubricant type, quantity and permissible operating conditions must be confirmed for the specific ZVL 608ZZ execution.
Factory grease should not be washed out, and shields should not be removed without an appropriate maintenance procedure.
Store the bearing in a clean, dry environment, preferably in its original packaging until installation.
The bearing has an inside diameter of 8 mm, an outside diameter of 22 mm and a width of 7 mm.
ZZ indicates two metal dust shields. These are non-contact shields that help retain grease and reduce contamination entering the bearing.
The standard execution without an additional C3 suffix corresponds to normal CN radial internal clearance.
Not automatically. They have the same dimensions and shields but differ in radial internal clearance. Selection depends on fits, temperature and operating conditions.
This may be possible after comparing complete designations and technical specifications. Matching dimensions of 8x22x7 mm alone do not confirm complete interchangeability.
No. ZZ shields reduce contamination entering the bearing but do not provide protection equivalent to contact seals.
Bearings with shields on both sides are generally supplied with grease. The exact lubricant specification should be confirmed for the manufacturer's particular execution.
The permissible rotational speed must be determined from ZVL catalogue data and the actual operating conditions. Speed ratings from other manufacturers' 608ZZ bearings should not be used as substitutes.
ZVL 608 ZZ is a single-row deep groove ball bearing from the Slovak-origin ZVL brand, measuring 8x22x7 mm. It features two non-contact metal shields (ZZ) and normal CN radial internal clearance. Its construction accommodates radial and bidirectional axial loads. When selecting a replacement, the manufacturer's load ratings, limiting speeds and application requirements must be verified.
The specialist B2B industrial trading platform simmering.pl supplies ZVL bearings for industrial, maintenance and technical applications. Product selection is based on complete catalogue designations, dimensions and operating requirements, with worldwide shipping from stock in Poland.
Data sheet
You might also like